Search results for query: *

63 dart 360. (273 64-66 V8 mts). On which side(s) do the tall/short ones go? I am way too high on the pass side (508 rubber insulators both sides). maybe I have the eng off sideways with the mtr mt slotted hole(s) in the kmember allowing alot of leeway for positioning side to side. thank you for...

are drivers & passenger side mounts the same height? and do you have any part #'s for em? thank you for your time. RR

63 dart stock car. 360 SB. what is the best flowing ex manifold to search for? has a thin shaft aftermarket steering column. thank you for your time. RR

63 dart was a /6. has the 3 mounting holes in the firewall roughly in a triangle. will a 64-66 A body V8 throttle bracket/cable bolt into the same holes? thank you for your time. RR

63 dart 360 in OE location. i had drilled the firewall for 2 holes for a later A body pedal/throttle cable but it is way to long. I found some cables on Ebay but they appear to be too long. I thought about shortening the cable I have & recrimping everything but I dont think that is doable. any...

'66 dart 360/904 stock car with aftermarket thin shaft steering column. Is there any way to lower the engine and or kmember to get my driveline angle right. I have raised the engine a bit & slotted the bolt holes/lowered the steering box so the magnum ex manifold on the dr side would clear the...

I am wanting to add a scallop to the other side of the crossmember so the dual exhaust will tuck up nicely. I have an extra crossmember. should I cutout a scallop then weld in some material or cut em both in two & weld the 2 good halves together and should I have it mounted in place for dead on...

where can I purchase one, to reduce filler neck ID to match thin gas pump nozzles. thank you for your time. RR

having starter to a swapped different ex manifold clearance issue. I under stand that the super compact mini starter from a 2007 dodge ram with a 5.7L MANUAL TRANS is what I need. how do I ID it so I can make sure the yard is selling me the right one? thank you for your time.

63 dart 360/904. the custom ex pipe down from the ex manifold that I want to go with is too close to the starter body. how much skinnier is a mini starter? Stock car & no ex wrap is allowed. and is their a starter wrap or heat shield for this. thank you for your time. RR

the thick "brick" ones with the 2 metal "lips" opposite of each other OR a thinner set/no lips that I see on Ebay listed for 64-66 A body 273? Thank you for your time. RR EDIT I reread the thinner ones descrip & it says for 64-69, not 64-66 if that makes a difference.

does anyone have a part # for these, iirc it was for a 1990 dodge D250 diesel. thank you for your time. RR

how much of a job is it to add air conditioning to a non air car (65 dart)?. at home or a pro shop handle it? R12 or 134A ?. thank you for your time. RR

what is a good/stout/long lasting brand to get (part #'s appreciated). thank you for your time. RR

considering a set. is there a tire dia limit to be aware of/other potential interference areas? thank you for your time. RR

what are the best ones that fit & flow the best? thank you for your time. RR

1963 dart. what are the front & rear brake shoe diameters/widths? (9" on the dia I would assume). thank you for your time.

63 dart/63 kmember/64-66 A 273 mts (with the tab welded on one for a 360). Which black insulators should I use? the thin ones listed for a 64 V8 or the thick ones for the 63 slant 6. racing app & I do have the one mentioned further down, the one for the drivers side with the interlocking tabs...

they have a 1/2" stud on one side & (2) 3/8 fine thread studs on the other side. what yr/make did these come from? Thank you for your time.

next years' 63 dart stock car, I will be purchasing the widest radiator that will fit (side to side). Thank you for your time.

A local guy on CL has a new rad for a 92-94 jeep grand cherokee/92-3 grand wagoner V8 for cheap ($75). I was thinking some had said that this is a good fit/choice on an early A body. Thank you for your time. RR