Recent content by BooW

  1. BooW

    Need pro advice Project X Block build Long term project.

    Hi , thx for all the input and answers good to know that i probably can leave the grooves :D What about oil control for maybe 7000 rpm. Whats the right way to go with? windage tray, HV oil pump , maybe better pan with baffles and larger tube for the pickup?. Take care
  2. BooW

    Need pro advice Project X Block build Long term project.

    in future i will order a custom converter :D, how is it to run a solid roller on the street, just about the maintence, i´m looking towards a bigger hydralic flat tappet.. ? hmm... just for the simplicity.
  3. BooW

    Need pro advice Project X Block build Long term project.

    Thx for input, didnt know that. good point there, this engine will be long term project, i´m seeking for the best knowledge out there. take care
  4. BooW

    Need pro advice Project X Block build Long term project.

    Hi thx for your input, Hmm seems good for the high winding power, is it any oil modifications need to been done the the block i´m thinking that cam going to min 7000rpm, that you said, maybe backdown a cam a bit. :D
  5. BooW

    Need pro advice Project X Block build Long term project.

    Hi guys come across a unused X block and some other parts here in Sweden, the only thing that has been done to it bored to std 340 and prepared for boost, the block has a O ring on top of the deck. 4 bolt mains ARP studs. I have used good (truck) forged crank that i´m planning to use and new...
  6. BooW

    Pushrod question.

    he was swedish , so thats why answer in swedish lang.. :D hahahahah
  7. BooW

    Pushrod question.

    Beskriv ljudet, vad har du för olja i? viskositet? vad är det för motor? topplock? geometrin för vipporna är väldigt viktigt också. Vad jag har läst mig till så är ju deras kamaxlar rätt aggressiva, tack vare designen på loberna. Jag vet att lyftarna i USA har haft kvalitets problem så att det...
  8. BooW

    What do you guys think of the speedmaster bare aluminum heads

    Hi mine flows better then a stock Edelbrock performer RPM head, they have a good 5 angle valve job. BooW
  9. BooW

    What do you guys think of the speedmaster bare aluminum heads

    Hey here you have mine. New in here need some advice SB 360 Cam selection See page 3 5 angle valvejob. BooW
  10. BooW

    Distributor Reluctor Orientation

    Hi usually there are marks of one side, the pictures are correct. maybe they have installed it upside down ?.. just my thought //BooW
  11. BooW

    Speedmaster/Procomp Heads - New combo kit???

    Hi there,here you have some Flow info of my heads and picture.... https://New in here need some advice SB 360 Cam selectionwww.forabodiesonly.com/mopar/threads/new-in-here-need-some-advice-sb-360-cam-selection.384223/page-3 Observe that these one Flow better then a pair of stock Rpm heads...
  12. BooW

    Speedmaster/Procomp Heads - New combo kit???

    Yes they are, but i did have some trouble with the helicoils some of them had a bad installation from factory and its LA style. //Rob
  13. BooW

    New in here need some advice SB 360 Cam selection

    Hi To be honest, i dont get that one? Irony:rolleyes:?
  14. BooW

    New in here need some advice SB 360 Cam selection

    Hi here is The Flow numbers from The vendor, it is a Superflow 450 bench Headers is already on. take care
  15. BooW

    35% off SpeedMaster

    Hey look here have just bought a pair of speedmaster heads LA New in here need some advice SB 360 Cam selection
Back
Top