Recent content by dazedand confused

  1. dazedand confused

    Polyurethane control arm bushings

    so your saying a & b body uses the same upper and lower bushings
  2. dazedand confused

    UPDATE SS Springs issue fixed

    in my previous post about my 1965 Dodge Dart concerning my Super Stock leaf springs shackle issue to where the bottom of the shackles was facing towards the springs instead of facing towards down at an angle towards the rear bumper . I made reinforced extention blocks to fix the geometry issue...
  3. dazedand confused

    Polyurethane control arm bushings

    I'm currently working on a 1965-66 plymouth valiant 4 door 200 . I'm rebuilding the front suspension . I want to buy a kit from energy suspension of both upper and lower control arm bushings and even though I went on their website typed in the vehicle info and it pops up a kit for 1965 to 74...
  4. dazedand confused

    Back spacing for slotted mag rim wit 235/75/15 8-3/4 rear

    so now a new issue I currently have a pair of rims for the back of my stock tire wells on my 65 dodge dart the are 15 x7 and the tires are 235/75/15 I'm stay with that tire size but I know I need to swap rims to the correct ones . these 2 rim I measured from where the drum presses up against...
  5. dazedand confused

    Super Stock leaf springs

    They are stock brackets bolted to body
  6. dazedand confused

    Super Stock leaf springs

    I will find out this week . the back half of the car is currently sitting on 3 concrete blocks on each side and rear end is hanging from from shackles / KYB shocks. I have 2 slotted mag rims with tires I will mount them on the car . the other issue was brought up is if the car is driving down...
  7. dazedand confused

    Super Stock leaf springs

    Ok so as you already know I have The correct Mopar A-body shackles , front and rear mounting brackets and Super Stock leaf springs 20" up front and 35 " on back measuring from eye hole to center leaf spring stud. the bottom of the shackles is facing up towards the trunk floor . I know they are...
  8. dazedand confused

    1965 dodge dart 2 door : Issue with super stock leaf springs

    So for a couple of years ive been buying a part or parts here and there for my 65 dodge dart . These parts are A-body = 8-3/4 housing , 489 case , polyurethane bushings. The super stock leaf springs, stock Abody shackles and front hangers and rear mounting brackets for shackles came from Mancini...
  9. dazedand confused

    Early 60s 7-1/4 axle shaft seal fix for " obsolete parts"

    Did a part 2 video on this . Finally solved the issue I was having with early to mid 60s for the 7-1/4 rear end axle shaft seals . found out though much internet searching and measurements since O'reallys said that the axle seals are not available that the axle seals for a 1965 Ford Falcon...
  10. dazedand confused

    [FOR SALE] Slant6 carter 2 barrel candy cane kickdown linkage brackets

    I have 9 New hand fabercated reproduction plasma cutted slant6 carter 2 barrel candy cane kickdown linkage brackets made out of plates of steel that match factory thickness and was copied off of a factory bracket . I can make more ! Asking 15.00 + shipping. shipping depends on your location...
  11. dazedand confused

    HEI conversion question

    use the thermal paste not grease . got the plastic syringe of thermal paste from best buy electronic dept.
  12. dazedand confused

    Push Button Start

    How did you go about doing a no key ignition set up ? I'm thinking of doing a push button start on my 65 dart . I guess they call it a 2 step ignition switch ? other wise id do a regular push button but the toggle switch would be one of those all weather rubber push button 2 wire switches...
  13. dazedand confused

    [WANTED] 225 slant6 2 barrel bracket & kick down linkage

    I recently converter my 225 slant6 1 barrel to a factory aluminum 2 barrel intake with Carter BBD carburetor . I need the bracket that bolts to the exhaust manifold and the kick down linkage for my 904 automatic . I dont mind if you have just the bracket or the linkage but I prefer both and it...
  14. dazedand confused

    wanted : Super Stock leaf springs 65 abody dart

    I have a 1965 dodge dart and looking for a set of super stock leaf springs I live across the lake from Branson mo. 76572
  15. dazedand confused

    65 Barracuda die cast or plastic model

    still making these resin kits ?
Back
Top