Recent content by OUTLAW

  1. OUTLAW

    where to post DIY tools

    where do you post DIY tools and kwik tips at?
  2. OUTLAW

    strut rod nut size

    I have been a mopar freak since the mid sixties and have never run into this problem. I snapped off the threaded end of my strut rods trying to get the nut off. In the process of making a new strut rod I discovered that the threads are 14mm x2.0 . Has anyone else run into this? In have owned...
  3. OUTLAW

    using studs on my heads

    these are speedmaster heads (pro comp) and came with the studs, nuts and washers.I don't really care for the 12 point nuts -they seem really tall to me. I think I am going to just replace the nuts with regular grade 8 nuts
  4. OUTLAW

    using studs on my heads

    I have a kwik question about my small block. Iam putting new aluminum heads on my 360. The heads have extra thick deck surface (5/8 for angle milling) so I needed longer than normal bolts (actually studs) I installed the studs (just till they bottomed out) and Torqued the heads to 75#.Now...
  5. OUTLAW

    Disc conversion on 67 Dart

    Check out Scarebird.com I did mine about 5 years ago only cost me about $250 and they still work great today.
  6. OUTLAW

    Power steering gear box question

    hey duster.... I checked out bergman...nice product but a little expensive, but if I can't figure out my problem that may be the way I go...thanks Dano.... the headers are a set of polished stainless (I don't remember the brand). Everything else is OK....it is definately the way the tubes are...
  7. OUTLAW

    Power steering gear box question

    In doing a refresh on my smallblock '68 cuda, I am changing the heads and the headers. Problem is one of the header tubes (cyl. #1) is hitting on the p/s box, right at the sector adjusting screw. Never had a header hit there before. Looks like I would have to collapse the tube about 1/3 to 1/2...
  8. OUTLAW

    What spring relocation kit

    I used the Mancini kit without any problem. Infact it was about 1/4 inch wider than my frame rail which gave a nice little ridge to weld on
  9. OUTLAW

    Brakes losing pressure at red lights, any ideas?

    If there isn't any external leaks then it sounds like the master cylinder is bypassing back into the reservoir. Time to rebuild/replace/or upgrade the master cylinder
  10. OUTLAW

    At home flywheel balance....

    Well let me tell you that YES it can be done! How do I know ? I did it and ran the flywheel for 4 years. Ma mopar put out the specs when the 360 first came out showing where to drill , what size drill and how much to remove. I will see if I can find the paper work. I needed a flywheel for my 4...
  11. OUTLAW

    906 or 452 which is best overall

    I hesitated when asking this question. It seems whenever an opinion is wanted it turns into a war of words.As far as experience goes I have been building engines since the late 60's, both import and domestics. With that said, even I don't know 1/2 of what I would like to know and there is room...
  12. OUTLAW

    906 or 452 which is best overall

    I have been cleaning out my garage and storage sheds and pitching just about everything but mopar parts. I came across a complete 69 383 out of a roadrunner and a complete 74 440 out of a ????. The 383 looks like it had a million miles on it. But the 440 looks like it was just rebuilt...
  13. OUTLAW

    highway cruising with 4.10 gears

    I'm running 4:30 on 29" tall tires and it sure ain't a fun trip ! You will find every vibration,buzzing panel and strange noise after about 5 miles.... and it goes down hill from there
  14. OUTLAW

    valve lash question

    everything is the same except the ratioand overall lift
  15. OUTLAW

    Need an new driveshaft made. Who do you use?

    I had FastShafts do mine. cost me just under $300 and they hi speed balanced it -no problems www.fastshafts.com 1-800-622-6617
Back
Top