Recent content by TXBarracuda

  1. T

    Ammeter conversion and power rerouting

    Not yet. A bunch of everything else has taken priority. I have a new harness built and made up a cover plate for the new bulkhead connector, but I haven't installed any of it yet.
  2. T

    [WANTED] '65 barracuda 225 exhaust and 2 bbl intake

    Thank you for the offer Rug. I'm buying the one from tdemo53. I'm still looking for exhaust though.
  3. T

    [WANTED] '65 barracuda 225 exhaust and 2 bbl intake

    Looks like a simple enough fix. Either modifying the existing linkage, building a new one, or installing a cable. Great to know going into it, at least I can have a plan in place.
  4. T

    [WANTED] '65 barracuda 225 exhaust and 2 bbl intake

    I hadn't seen that in my searching. Good information to have though. I'll keep this single and use it to practice my aluminum fab skills I guess, thank you.
  5. T

    [WANTED] '65 barracuda 225 exhaust and 2 bbl intake

    Manual Sounds perfect! I'll PM you
  6. T

    [WANTED] '65 barracuda 225 exhaust and 2 bbl intake

    Looking for a dual exhaust (3-2-1) setup for my ride. Dutra dual type is preferred, but open to others. Also wanting a 2bbl intake to replace the 1 bbl. They seem to be hard to find. Open to suggestions as well. I've searched and searched, but everything I'm finding is bank breaking worthy.
  7. T

    Help to identify

    They are absolutely for the lights. I have no idea what the front of a rally dash looks like, but are they not indicator lights of some sort? It seems odd for 3 taps separated like that to feed dash lighting.
  8. T

    LED Dash bulbs

    At whatever level the dimmer came set at, it's eye friendly. My camera is just being a sensitive punk and makes it seem bright. It's cleaner, but slightly less than full oem brightness. Figured out a relative comparison for brightness since my phone camera is sensitive. The reflection is...
  9. T

    LED Dash bulbs

    Blue. Has less impact on night vision.
  10. T

    LED Dash bulbs

    Pwm dimmer came in, so strip LED mod went into effect. I'll take night time pics tonight. Red wire for "full brightness" is just heat shrunk and tucked, not connected to anything. I cleaned up the board and tinned all of the contacts, as well as soldered pins in place. This ride hasn't...
  11. T

    LED Dash bulbs

    Doesn't really matter which you get. Just make sure they're 12v rated. I have no doubt that they're all made in the same couple of factories. LED strip, then a pwm dimmer and you're set. Or, no dimmer and have them bright. I have not bought a set that comes with a power supply and a dimmer...
  12. T

    Rear end for 65 barracuda with 5x4.5 bolt pattern

    I don't recall any of the 8.8 measurements, but aren't most of them off center as well? Not a deal breaker, but would require more work than simple bracket welding.
  13. T

    LED Dash bulbs

    I figured. I really like your idea, and I was researching making led strings dim. Due to design, they really don't like dimming the same way incandescent bulbs do. A pwm dimmer essentially turns them on and off really quick to give the appearance of being dimmed. I found these and put a...
  14. T

    LED Dash bulbs

    Do they dim with the switch, or did you have to use a pwm dimmer?
  15. T

    Light switch relay

    It's a single point of failure as it is, with a higher probability wired orm style. Headlight relays alleviate almost all of the risk. The extra stuff I'm thinking of doesn't change any risk, just changes where the failure would occur. 50 year old light switch, or new fuse block. However...
Back
Top