[SOLD] 1973 Duster parts car, will cut small patches

-
Status
Not open for further replies.
Yes but I dont need the rear brace area where the bumper brackets go through. I will try to save your picture and highlight what I need.
 
I need the yellow part. If you can cut it 10 inches from where the rear shackle mount stops towards the axle. I dont need any of the stuff I put in red. If you need more info let me know and I can call you or something. Hope this helps.

Screenshot_20190104-214048_Gallery.jpg
 
I also need the part of the frame rail where it spot welds to that rear panel. If you want to leave some of the rear brace panel on it that's fine I can drill the spot welds out and remove it. I dont need the bumper mounts so keep those and sell them to somebody.
 
I'll either get it all cut today (wifes Bday) or tomorrow for sure and should be able to ship stuff on Monday. I'll trim off what not needed and remove the bumper mounts
 
I'll either get it all cut today (wifes Bday) or tomorrow for sure and should be able to ship stuff on Monday. I'll trim off what not needed and remove the bumper mounts
Tell your wife Happy B-Day!! Let me know the shipping cost and how you want the payment. Thanks
 
Thanks, I did, she said thank you! I got your pieces rough cut and will finish trimming them down this afternoon. I'll get them in a box and PM you the information.
These pics are for shakedown scott, check your PM's.

IMG_1455.jpg


IMG_1456.jpg


IMG_1457.jpg
 
Plymouth67, clear out your inbox and PM me your adresss info. I got it all cut and need your zip to get a shipping price
 
FC23DCAC-8E66-4502-9FDC-67193BF3A04D.jpeg

I could use a piece of the right inner fender to patch a hole where the fenderwell headers went through. It’s not a big piece and could be cut in front of the shock tower a couple inches and just above the frame rail so don’t have to drill out any welds.
Also at the firewall you could cut to include a small strip of the firewall where inner meets it. Again no welds for you to drill out l’ll do that. Shipped to 43571. Thanks
 
Dartski, you have a pm about the patch piece.

QuickDart360, The chrome is good driver quality. Here's picture and I'll add another tomorrow. I want $40 for the bumper. I'd guess shipping would not be cheap as that thing weighs probably 80+ lbs, but I can looking into if you're serious as Greyhound would be the best option.

IMG_1391.jpg
 
HI I could use a small section of lower drivers rear quarter right behind rear wheel with a section of the trunk extension attached.Let me know the condition when you get a chance.Thanks
 
At the base of the back window there is a horizontal piece of window trim I need for the R (pass) side if made of stainless. Still in pic so perhaps still available?
 
STRorange, Its got drum brakes so the upper arms are probably small ball joint, I'll check tomorrow. If you need a steering box (I'm keeping this one) check out Rockauto and Lares #18831 16:1 (fast ratio) manual steering box, new no core for $316! They also offer remans too (I looked under Dodge, 1973, Dart, 340, steering) Discount codes are all over the internet, here's one for 5% off, 9753920291539131

Dartski, here are the pics of the two panels I have. The yellow is really nic, but doesn't have much of the firewall flange. Obviously the blue one does and I'll cut it roughly where the yellow paint is. Let me know which one if you're still interested

IMG_1506.jpg


IMG_1507.jpg


IMG_1508.jpg
 
I did save the spare tire well, its pretty good except for some small rust through where the hold down bracket is, but its definitely not perfect. $20 + shipping

IMG_1509.jpg


IMG_1510.jpg


IMG_1511.jpg


IMG_1512.jpg
 
I did save the spare tire well, its pretty good except for some small rust through where the hold down bracket is, but its definitely not perfect. $20 + shipping

View attachment 1715280848

View attachment 1715280849

View attachment 1715280850

View attachment 1715280851

Hey, thanks for the detailed pictures and description man. I appreciate it. Very fair price, but I'm gonna pass as mine is pretty much in the same shape.

Thanks again for taking the time to post up the details.

Be well,
Pat
 
Status
Not open for further replies.
-
Back
Top