Road Racing Duster 6.4 Hemi E85 6 speed Ms3 Pro Evo EFI
Update: I ordered the Bouchillon Gen 3 Hemi throttle cable and bracket that was 167 shipped. Waste of money. It only apparently works perfectly if you use the old BBK driver side throttle activated TB. You can force it to work with an LS TB, but you have to still rig up a bracket to mount the bracket it comes with to get the throttle cable geometry correct (as close as possible). The bracket seems to be the only thing made, the cable looks to be a stock GM cable. The tube that is made of plastic and goes into the car, is to long and hits the back of the pedal, so you have to trim it, waste. The tube the cable is in, is also a very semi bendable plastic, however you have to drill the hole of the stock location cable to .660, which puts it right near the valve cover.. i had to clearance the plastic covers to get the push/lock piece to seat properly and not over bend the cable. I *Highly* suggest for anyone doing a swap to get the cheapest and longest universal cable and make your own bracket.
I will making this one work for “now” and when the car comes apart to repaint the engine bay later down the road I will be replacing it. Also if you wanted you could buy the stock throttle cable for like 30 dollars and then make a bracket, like this one: https://www.partsgeek.com/kcxw8fx-g...NDKpvAlwYfFxM9wnz6AiAgzCWhl7akPxoCiZIQAvD_BwE
My plan is to make a bracket off of where the front passenger fuel rail bolt is and bolt their bracket to it. I’m also looking for a ball cup to insert the safety wire cable into and mount to the throttle ball casted into the throttle lever since the piece they supply is too large for any of the holes and would require me to attempt to drill the holes larger, which I have no issue with, but I much prefer to attempt the ball cup setup first and then find the cable holder for an LS cable next. Using the ball/cup will allow me enough cable to not have to make a huge bracket. So we shall see
Attached is a photo of my Tb. (Mines 92mm) The piece that I’m mentioning as a ball and cup is the piece I believe is used as a kickdown attachment.. I’m looking for something I can attach to the end of my cable and pop on here
Update: I ordered the Bouchillon Gen 3 Hemi throttle cable and bracket that was 167 shipped. Waste of money. It only apparently works perfectly if you use the old BBK driver side throttle activated TB. You can force it to work with an LS TB, but you have to still rig up a bracket to mount the bracket it comes with to get the throttle cable geometry correct (as close as possible). The bracket seems to be the only thing made, the cable looks to be a stock GM cable. The tube that is made of plastic and goes into the car, is to long and hits the back of the pedal, so you have to trim it, waste. The tube the cable is in, is also a very semi bendable plastic, however you have to drill the hole of the stock location cable to .660, which puts it right near the valve cover.. i had to clearance the plastic covers to get the push/lock piece to seat properly and not over bend the cable. I *Highly* suggest for anyone doing a swap to get the cheapest and longest universal cable and make your own bracket.
I will making this one work for “now” and when the car comes apart to repaint the engine bay later down the road I will be replacing it. Also if you wanted you could buy the stock throttle cable for like 30 dollars and then make a bracket, like this one: https://www.partsgeek.com/kcxw8fx-g...NDKpvAlwYfFxM9wnz6AiAgzCWhl7akPxoCiZIQAvD_BwE
My plan is to make a bracket off of where the front passenger fuel rail bolt is and bolt their bracket to it. I’m also looking for a ball cup to insert the safety wire cable into and mount to the throttle ball casted into the throttle lever since the piece they supply is too large for any of the holes and would require me to attempt to drill the holes larger, which I have no issue with, but I much prefer to attempt the ball cup setup first and then find the cable holder for an LS cable next. Using the ball/cup will allow me enough cable to not have to make a huge bracket. So we shall see
Attached is a photo of my Tb. (Mines 92mm) The piece that I’m mentioning as a ball and cup is the piece I believe is used as a kickdown attachment.. I’m looking for something I can attach to the end of my cable and pop on here