Search results for query: *

Sorry John !

If it's a rubber squeak it probably means a torn bushing. None of the rubber bushings get lubricated, with normal function the rubber doesn't slide or spin on any of the surfaces. The normal suspension movement should just be the rubber flexing one way or the other. So if you have a rubber...

if you have basic mechanical skills, yeah you could tackle it. but go in knowing that it's bone crushing knuckle busting work that will slap *** wear you out. the only special tools you'll need are for the upper ball joints, but you can rent the socket. the lower control arm bushing r&r is...

^^^^^^^"Shady spot" :rofl: :rofl::rofl:

The first tunnel ram I had the carbs sat sideways. It would have required the right side insert to be partially cut or at least that area. So, I ran without a hood for a while. This intake allowed me to change the carb placement so I went with it. The offset is noticeable but, that’s how these...

A bit more progress on building the shelter today. Of course Gracie helped and subsequently laid claim to the totally OSHA approved shady spot. Where she could boss me around.

Was...... But the upside of that story is that I was more in love with Mopars, and had two at the time the Corvette was stolen. The Insurance Co. paid me enough to buy my House in Viet Nam.... :thumbsup:

You COULD take the dog for a walk…just sayin’…

Dash cluster looks excellent, can’t wait to see it lit up

Beautiful car Mitch!

I found and bought my 1960 fuley Corvette when I was 19. It was a mess of course. But I was young and learning, and I restored it. Had that car for 40 years before someone stole it. I always had an affection for the 63 to 67 coups. I would have traded that car for a '67 big block, 4-speed coupe...

That's interesting. I would have argued that the 650 number was maybe someone misreading it (6 does look like 8). I've always heard of them as rated at 800 and 850 cfm. Looking at the list of TQ numbers, it does appear that the later E58 motors did get the smaller (1 3/8" primary) TQ, so that...

Can do the same "Lift" test with a hand held dial caliper. Simple, easy to read, and everybody owns one. ☆☆☆☆☆

I know MH can't sell SOME stuff direct(fb rear cargo light harness they can and will). My point was you don't have to deal with Year None to get an MH harness, as I've shown in the link above. I would rather deal with smaller Ma n PA operations than ever have to deal with Year NONE again.

Haha definitely have done that before

Believe it or not lash widens with heat.

Adjust with what the lash is supposed to be. After you break it in, check them again. The lash will open up roughly.005 from cold to hot.

And it still works….. :rofl:

i'm in the same boat. i'll take capable over a hotrod 9 out of 10 times. but that 10th time, i'm gonna want something really wild.

Obviously, what looks good is in the eyes of the beholder. Only one of the above appeals to me, #13, but looks to have the car to back it up. So, you are the beholder, do what you like.

Here is the factory offerings for '75 - https://www.hamtramck-historical.com/images/dealerships/DealershipDataBook/1975/75-1-Dodge-engineering_0004.jpg Note that there were two versions of the E58 that year, federal and CA. For the federal motor, torque peak RPM is the same as for the '74...

:rofl: :rofl::rofl:

Bad locator hole - out of round.

Some on eBay (with glass+) 1968 1969 DODGE DART AND BARRACUDA CONVERTIBLE QUARTER GLASS LEFT CLEAR 1967 ?? | eBay 1968 1969 DODGE DART AND BARRACUDA CONVERTIBLE QUARTER GLASS RIGHT CLEAR 1967 ?? | eBay 1969 dodge dart convertible driver left quarter glass frame molding clear 1968 | eBay 1968...

Pressure test. Or fill it with epoxy block filler, set the piston to wall and ring gap to air cool specs, and run it on methanol...

FS-69 Dart dash pad black used it’s the original from my 69 Swinger,both corners are split,center leading edge is also broken,cracked,the top is crack free & looks good $100. U pay shipping

Full disclosure I have not liked Vettes since about 65-68, those made me pant. Since then? Hard pass. But……. The 2024 version I have to admit is so Maclaren like, that frankly I really like it. I went so far as to explore costing. I think they are totally BA again. I know that is blasphemy on...

Gef is gonna be the guy, one of the leaf spring pads has a bad location hole in it.4-1/2” BP 44” center to center on pads but photo shows bad locator hole.

Would need them shipped to zip 92675. Also can you send a picture and price? Thanks