Search results for query: *

  • Users: guido
  • Order by date
  1. guido

    Oil pan for 340 going into 1964 plymouth valiant

    I am in the process of installing a 1971 340 in my 1964 barracuda. When the 340 was rebuilt, they installed a 340 oil pan on it. I had almost fully installed the motor and I noticed the center-link hits the oil pan. on both sides. I am using the stock 273 exhaust for now and it also hits the oil...
  2. guido

    Which exhaust manifold bolts need thread sealer on a '69 340

    I purchased new studs and installed them with sealer as instructed above. Thank you very much to everyone at FABO
  3. guido

    1965 Federal pump issue with a new Borgeson steering box Please Help

    Hi Guys, I just installed a New Borgeson small sector power steering box in my 1965 273 4 speed barracuda. The box went in quite easily. but I have a problem. The federal power steering pump which worked perfectly with the old... stock 'Gygundic' [huge and heavy] steering box does not work at...
  4. guido

    My 2nd sealing question, which water-pump bolts on a '69 340 need thread sealer

    Thanks Guys!!! For all the help. Just to be safe... I'll seal All of them, it can't hurt Angelo aka Guido
  5. guido

    My 2nd sealing question, which water-pump bolts on a '69 340 need thread sealer

    I am pretty sure I know but I don't want to make a mistake. And which thread sealer should I use. Thanks Guys.
  6. guido

    Which exhaust manifold bolts need thread sealer on a '69 340

    I just want to make sure I am sealing the correct studs-bolts when I install the exhaust manifolds. So... I don't have to do it twice. Also, any recommendations on which thread sealer to use. Thanks guys, for the help
  7. guido

    Radiator that will fit my 64 barracuda for a 340 upgrade

    The bottom hose is on the driver side, the top hose is on the driver side of cap to clear my AC. I believe the water pump is the 69 style. I changed it to match up with the radiator that was in the car. Now I know the current radiator is for a mustang and was mickey moused and too small. So I'll...
  8. guido

    Radiator that will fit my 64 barracuda for a 340 upgrade

    I am leaning towards the 3 row. The 4 row feels like overkill for my 340. I have a stock mechanical fan now, and a pusher electric fan that kicks on when the AC is on. I'll start with that. If it over heats, I'll replace the mechanical fan with the Derale shroud and fan, with their variable...
  9. guido

    Radiator that will fit my 64 barracuda for a 340 upgrade

    OK I measured the 1964-1/2. The Champion MC64DT radiator dimensions appear to be correct for my 1964-1/2 white/gold 340 mild cam 3.91 gears push button auto barracuda except the top inlet would have to be moved to the driver's side because of my aftermarket AC. Ledfoot racing will sell me the...
  10. guido

    Radiator that will fit my 64 barracuda for a 340 upgrade

    Sweet car!!! Thanks for the radiator P/N. looking it up now. I do need the top outlet on the driver side of the cap to clear my aftermarket AC. The CC1635 Champion recommended appears to be too tall. I just measured my 65 see pic. The 64-1/2 is at my friends shop hopefully the 64 dimensions are...
  11. guido

    Radiator that will fit my 64 barracuda for a 340 upgrade

    I am swapping my 273 for a 340 into my 1964-1/2 barracuda automatic push button. Looking for recommendations on what radiator will fit. I am concerned about the radiator cap hitting my hood. Champion said their CC1635 will bolt right in, but I am afraid it will be too tall and the radiator cap...
  12. guido

    273 to 340 swap in 64 cuda auto advise needed

    OK it's been a while since I replied on this post. The day before I got the rebuilt '71 340 motor from the shop. My wife and I got t-boned by a girl on a cell phone who ran a stop sign while we were stopped dead in traffic. 23K worth of damage to my car. The body work is now 40% done so I...
  13. guido

    Thermostat and housing

    This is what was on the intake with no thermostat. It came with a o-ring and no recess for a thermostat. Is there a Motorad style with the t-stat recess like the 4830kt housing but with the neck at this angle so I don't have to buy a new top radiator hose? Most pics on the internet don't show...
  14. guido

    Thermostat and housing

    I just ran into the exact same problem. do they make these housings with the neck at an angle instead of straight up?
  15. guido

    Strange torsion bar issue on my 1965 barracuda. Please Help.

    Great answers!!!! I reached out to Bergman Auto Craft they recommended 1.08 torsion bars, Bilstein shocks Dynamic strut rods and offset upper control arm bushings to increase camber. I am concerned about 1.08 dia torsion bars being too stiff. Any thoougts? Who else sells torsion bars for the 65 cuda
  16. guido

    Strange torsion bar issue on my 1965 barracuda. Please Help.

    Hi Guys, I wasn't able to read the stamped numbers on my T-Bars yet, but I measured them from underneath at about .860 to .880 or so in diameter. Does anyone know the torsion bar p/ns. [I know there are 2 p/n's, even and odd, for left and right side]. Here is my problem. I crank in the...
  17. guido

    [WANTED] WTB Passenger side upper control arm with all the bolts and ball joint for a 64 Barracuda

    Hi, My 64 Barracuda got t-boned last summer and the repair is moving along. I need a complete Passenger side upper control arm assembly, with all the bolts and the ball joint. Thanks, Angelo aka Guido
  18. guido

    Changing a floor 4 speed shifter to a 4 speed console shifter on a 65 cuda

    Hi JD, I am making some progress on installing a b body center console into my 65 a body 4 speed cuda. I found this '4084' shifter handle that will bolt up onto my 4 speed hurst shifter. It should bring the shifter handle into the center of my tranny hump. It looks like I will be able to mill...
  19. guido

    Changing a floor 4 speed shifter to a 4 speed console shifter on a 65 cuda

    Hi Mike, You sent this to me before and I didn't get how that was to help me with my 4 speed B body center console in a 65 A body cuda project? What am I missing? Angelo aka Guido
  20. guido

    Changing a floor 4 speed shifter to a 4 speed console shifter on a 65 cuda

    Hi, Here is the pic again of my 64 barracuda with stock seats and a center console from a 64 automatic dodge polara. [the tach is from a 64 GM car]. I purchased brackets online and moved both seats out towards the doors after removing the broken seat belts and the center console fit in. I milled...
  21. guido

    [WANTED] waterproof car cover for a 64 barracuda

    I have all the body parts to fix this except for the aluminum rocker panel sill plate. Laysons has it on back order. After they pull the hinge pillar and rocker panel out on the frame machine... they said we may need to have a rocker panel and hinge pillar cut form a junk yard donor car. Then...
  22. guido

    [WANTED] Dash Pad wanted for a 1965 barracuda

    thanks for trying but ur correct its a bit rough
  23. guido

    [WANTED] waterproof car cover for a 64 barracuda

    Does anyone have one? or a recommendation on a good one to buy? I have to cover it while outside at the body shop Any thoughts on a 'carcoon' type inflatable car port?
  24. guido

    [WANTED] Dash Pad wanted for a 1965 barracuda

    Not the entire metal dash, just the vinyl dash pad that get's dyed then glued to the dashboard
  25. guido

    [Found!] WANTED: 1964-65 BARRACUDA/VALIANT LICENSE PLATE LIGHT ***'Y

    Thanks everyone I bought one on ebay
  26. guido

    [Found!] WANTED: 1964-65 BARRACUDA/VALIANT LICENSE PLATE LIGHT ***'Y

    Looking for a 1964-65 License plate light complete assembly, maybe even the same in 66. I am thinking Valiants and Barracudas in that year range may be the same here is what one looks like from a barracuda
  27. guido

    65 valiant license plate light assembly

    here is mine from a 1964 barracuda
  28. guido

    [WANTED] license plate light ***'y for a 1965 Barracuda

    Hi, I am looking for a complete license plate assembly for a 1965 Barracuda. See picture. The mounting screw spacing is 7.5 inches
  29. guido

    Clutch kit recommendation needed

    how is the pedal pressure? and no chatter I assume
Back
Top