Search results for query: *

I believe that is the 4 pin one for the hood. The trunk one has 2 pins.

It looks like it turned out to be a 2839928 or 3504199. I need one if anyone has a decent one.

Need one of these. 2839928 or 3504199

Thanks for the replies. But I'm kinda stuck with the two holes on the lid. I'm figuring maybe the lid came from another year? Or something? Anyone have any suggestions? I didn't see any of the emblems that you guys told me about that has that stud pattern.

I have a painted 70 dart in my shop and I can't figure what emblem would have been on it. I'm not sure if the deck lid is from a 70 or not. I do see 2 holes for pins. See pics. Any ideas?

I'm having a hard time finding the correct gas cap for a 70 dart. I'm thinking it's a non vented cap since the filler neck is vented. Anyone have one for sale?

Hi I need a decent radio / heater bezel to complete my dash for a 70 Dart non A/C. Please let me know if you can help.

I am looking for a set of very nice doors for a 72 duster. I am hoping to find a set within driving distance of 15552, (sw pa) but I am open to shipping as well. Please, very nice only.

Looking for the post that connects the cowl to the roof. The inner part of the cowl is needed as well. Probably from the top door hinge to the roof would be great. Both sides.

Looking for a radiator support, bottom and sides, for a 72 duster non a/c. My zip is 15552.

Thanks

Hi. I'm assembling the tail panel and brackets on a 72 duster. I need pics from in trunk of the tail panel support brackets. Especially the brackets in the back corner. Any help would be greatly appreciated.

Does one of these eccentric go on each side of the rod that works the upper folding seat? Or is a bend in the rod what is supposed to be? Does anyone know where more of the eccentricsame can be found? Thanks in advance.

Located in SW Pennsylvania When: Saturday, Sept 20, 2014 - 11:00 to ? - Rain or Shine Where: New Hope United Church of Christ, 3404 Cumberland Highway, Meyersdale, Pennsylvania, 15552. The church is located on Pennsylvania state route 160 between Wellersburg and Berlin, half mile south...

I need two of the larger floor plugs for the inside and the plugs for the trunk area. I don't want to buy a whole set for just a couple of plugs. I would like them to be in decent shape. Anyone have these? Thanks FABO.

Thanks for the pictures. They should help. Looking forward to hearing from you.

Thanks for the reply both of you. Rocky. I sent you a PM.

When I orderd my carpet kit, which was supposed to have a 'console carpet kit' in it, I was expecting more than a rectangle of extra carpet 3 foot long and about a foot and a half wide. I was hoping the kit would contain the pieces I need roughly cut out and ready to fit. Also, when I bought...

Still looking for 68 Barracuda 4 speed console plates. Only 68-69 are the same. PM me if you have something you would like to sell. Thanks FABO

I am looking for a good set of 68 Barracuda seat belts. Bucket seats. I would prefer black but I can dye them as long as chrome and belt buckels are decent. Thanks FABO

I did most of the things you guys suggested and found that the when I bolted my dash tight inside the body, the warm ignition wires went away. Maybe it was missing a ground. I am using a Pertronix in my distributer. The red wire is supposed to hook to a positive source before it goes through...

I have a white washer bottle I bought a long while ago that is the one that needs an electric motor added for the pump. I'd like to trade it for a new white washer bottle that is made for the foot pump. Should be for any 67-69 A body I'd think. Thanks FABO

I connected a battery to my 68 barracuda a few days ago to start checking everything electrically before I start turning over the engine for the initial start. I restored the car from ground up and replaced the dash wiring warness with a used one. I went over the harness and repaired what was...

4 Speed Console Plates - Looking for a driver or better set of 68 Barracuda console plates. I think the storage cover can be either an automatic or 4 speed, but the shifter plate and ash slider must be from a 4 speed. Black inner A-Pillar trim pieces - Nice ones only Black Kick panels - Nice...

Everco H1954 Heater Valve Plymouth Valiant Dodge Dart 1970 1971 Mopar A Body Brand new and in the original box. I bought this for my 68 Barracuda but the inlet and outlet is too small. My loss. maybe your gain. $35 + shipping OBO. I can send a pic if you would like. Thanks FABO

I am still looking for a decent right Defrost vent tube for a 68 Barracuda with A/C. Thanks FABO!

I need the following for a 68 Fastback Barracuda 1 - A couple of those white plastic oval shaped clips that hold on the lower back window trim. 2 - A right defroster vent hose. (Mine is A/C. Not sure if that matters.) 3 - The two lower pieces of metal trim that goes in the fastback area...

When: Saturday, Sept 21, 2013 - 11:00 to ? - Rain or Shine Where: New Hope United Church of Christ, 3404 Cumberland Highway, Meyersdale, Pa. Route 160 between Wellersburg and Berlin, ½ mile south of the old Rainbow Lounge and about 2 miles north of the Twin Churches. See directions below...

What the heck did they paint the interior wheel well panels and the one side of the plywood with? It is very hard to sandblast. It feels like some kind of bed liner or under coat. I have two sets and both have the same paint? What would I use to duplicate this finish. Thanks FABO!

I am in the process of putting my 68 Cuda back together and I am having back up light woes. My 4 speed tranny has a reverse switch on it. When I took it apart, it had a two tan wire connector that was melted off near the exhaust pipe attached to it. I could not figure out where the other...