Search results for query: *

Flat tappet solid lifters Reground by Delta Camshafts Started life as Hughes lifters 20 years ago. Was going to use them in new build, but decided to go with EDM cool face lifters $150 plus ride located 99323

Yes. Stock repro k-member or a motor plate if you follow TTI’s motor position requirements.

Nice work, as stated, dividers look great. 65

Eagle H Beam Connecting Rods for SB CRS6123C3D Low use, comes with new ARP 2000 bolts Had to go with lighter rods to achieve balance $675 new with ARP 2000 bolts asking $400 plus the ride located 99323

There's a stock (4bbl & headers) magnum 360 vs 410 but they added almost 2 points of compression when they stroked it, it gain 29 hp, 305 hp vs 334 hp but obviously a chunk of it's from more cr. There's also a more performance build 360 vs 410 using same parts think it was Edelbrock headed, and...

I ran across a 62 toad that was a gasser project down in Florida. Was a nice start on it but he wanted $7500 . So I had to walk away. But it was a cool car. .

GTS or Swinger? Vans has Swinger grilles that look nice.

I am pretty sure I noticed my oil filter going into bypass mode on cold starts last winter.. the Pressure gauge read 5-7 PSI lower than normal until the oil warmed up a little.. That was on a slant six with 80K. Recent oil pan removal for dipstick soldering, and paint. Valvetrain looked clean...

you could get real trick and run the fuel cell mounted on a scale, just keep and eye on the weight remotely...aircraft style. "I got 35 lbs, Im good!"

Looks good! I set up a table in the bathroom and trim the gaskets in there. Otherwise, I am always in to big a hurry and rush thru and screw up the center dividers to many times (End up being very skinny). I have plenty of time while sitting there!

:rofl:

Blast from the past, wow took this 8 years ago already, been driving her for six seasons now! It was a lot of work but worth all the effort. For those still slaving away on your rides just keep trying to get some goals accomplished each week and you’ll get there and the rewards when you...

Got a 67 Dart with a humble 273 with a Dakota mini starter with the original 67 battery cable hookup. The starter has the cable relocation kit. I’d like to keep it. The problem is the SB cables just barely fit on the starter including having to pull the cable out of it’s firewall bracket. The...

Got it

Nice work

Yes, MDS, lifter still spun free, soft cam or oil starved is the popular diagnosis, the rest of the motor was fine, 110k miles, no sludge buildup. I have it down to the block now,cam and rod bearings look OK mains look not the best. Crank just needs a polish, will replace all the bearings.

He usually still holds .01 as you’ve probably noticed. Canceled time trial for tomorrow so they can get more racing in.

To these heads. (BPE) Intake ports are 2 1/2" tall and a few thousandths wider than standard gasket opening size. Gaskets hung over the roof and floor too much to leave alone. Looking down the runner through the plenum things line up much better now. So (thankfully) this is an older Super...

Hopefully he keeps trusting the car, it's on a rail, consistent.

Looking for windshield trim from 1968-1976 A body two door hard top.

is this the drive up oil change place?

Brewers sell a composite floor hump for that application.

…

Oh okay, guess it helps to know the lingo since I haven't been but a sleeping beauty lol. Thanks John

:popcorn:

New in Box Power steering pulley with keyway style fit. From CVF. $45 + shipping CVF Stealth Small Block Power Steering Pulley - Keyway

An acquaintance of mine had built two big small blocks. His first was a 471(r block, I believe) with some sort of W head on it. It was a street driven (frequently) 71 demon, nine second car as it drove in the gates, cover car for a couple mopar magazines. I beat him once, heads up, with my...

MDS doesn't have ANY bearing on cam failures. I've seen NON MDS lobes fail as well. The only real common denominator is VVT engines. I have seen lifter failures in the 30-08 engines, due to extreme non-maintainance.

New 67-72 Non-A/C heaterbox rebuild kit Retails at DMT for $64.95 I’ll sell for $40 + shipping