Search results for query: *

What can I do to make my car have this stance without going to air shocks?

Correct diameter hose is also available from Nappa. https://www.napacanada.com/en/p/UNR23840?srsltid=AfmBOorZkf0XXUXjYsMxdGoStWqrbZHun18_i88sihgDMk0bBmyNiEMy Here's the Nappa Part Numbers for my American friends.. https://www.napaonline.com/en/p/NOE96004...

What was

certainly appreciated, I don't remember any instructions with the struts but I think the proprietor was very approachable. Kinda wish they still did individual suspension parts. Im kinda partial to the old Mopar front end and spring config. Additionally, YouTube is full of folks doing front...

I have a 72 Dart 318 with 4 wheel manual drum brakes on 14" wheels. I want to convert to disk brakes. I would like to replace front and back and add vacuum booster. Everything I've found says I have to convert to 15" wheels. Is there a disk brake replacement for 14" wheels anywhere out there?

Welcome from West Virginia……….. :thumbsup:

I suspect Dana's point was that there should be no voltage drop with the key on or off unless something besides the ignition and field are drawing power. Voltage drop only occurs when current meets resistance. Key on with a normal ignition and field should draw no more than 5 amps. The...

Shipping would be about $20

They are offshore sourced like all after market rods these days. The bearing bore and pin bore measured good. They weigh 705 grams. I ran about 30 1/8 mile passed on them. They were just a bit too heavy to balance my crank without using Mallory metal.

Yup. Some days suck harder than others but you can't quit. I can't quit anyway. If I just sit around I'll lose my mind (what's left of it) and my body will lock up. I'd rather be dead than live like that.

Pics of car

Hi All: I just posted the latest chapter to my component restoration series under the title "Bob's Component Resto, Chapter 37: The Defroster Hoses". You can find it under "Member Restorations" in the forums section. I've come up with an affordable solution to replacing those old rotten factory...

Someone is always worse off than you and me, so I’ve decided to stop whining, push as hard as I can and empathize with those truly worse off than me.

Hey Pittsburgh, what do you think of those Trickflows? The Mopar ones.

NICE------AND-----SUBTLE!!!

Hello MoBros and MoSis'. I trust all is well with you and that you've been sleeping well of late. If not, I'd like to present my latest component resto chapter: the defroster hoses. Guaranteed to put you to sleep! So let's get right into it. Is there a single member of the Mopar...

Weather Channel now should say "Trash programming crying about climate change"

Hi I received an email if i entered my Vin Number i could get more info about my Dart ,now i cant find it .Any help .Thanks

The bypass valve is in the oil pump.

Fords, have you seen their connecting rods lol

I'd buy them.

I like to generally see 1 to 1 1/2 thread below the rocker. All the adjusters I use have a recessed area in the adjuster and that needs to line up with the oiling in rockers, If the pushrod is too long or short the rockers can't oil and that will burn up the top end in short order!

My son needs two of these center caps. They are for a 77 New Yorker. I think some of the 70s Dodge trucks also use the same cap. Thanks.

I had a 380zx. I really liked that car but was underpowered

KH

It just so happens that the GM 6.0L LS2 was a stout engine that had a higher ratio of exhaust flow. It really helped that engine breathe and gave increased flexibility on cam design.

You used the same steering wheel as I did on my Duster.

All I know is I'm just not anal enough to really care!! I stopped crunching numbers and such way back in the late 90's! :poke: