Search results for query: *

Rocket, I cleared my PM messages. Left you a message.

So I'm an idiot. I can't figure out how to delete old PM messages

These are the rockers for W2 race heads and not the econo W2; correct?

Does anyone have any blue Mopar or Gold Crane 1.5 exhaust rockers for W2 heads? This the offset shaft style used with aluminum rocker stands.

I'm looking at big inch SB stroker kits from Ohio and Hughes based on a 360 block. Ohio has a 4.1 inch crank kit that'll go 425 inches with a 4.060 overbore, (418 with a 4.030 bore). Hughes is 4.180 stroke with a 4.030 bore for 426 inches. This will be a drag race only engine in my Dart. I'm...

Are you using a high zinc oil?

I assume it's this pulley. Only one that Moroso shows.

I meant the passenger side, not the drivers! Dislexia!

Guys, Thanks for all your comments! It looks like I'll figure out a mounting in the normal drivers side area. I'll use a smaller pulley as suggested and will have a cut-off switch for the alternator while racing, which should keep the belt on! Any pictures of your installations would be...

Do me a favor and send me a picture of the mounting of both the alternator and water pump. I'm trying to figure out which mounts to buy, and I really don't want to spend a lot of money if possible!

Anyone running an alternator with an electric Moroso belt driven water pump kit? I have a 68 Dart race car with a 360 LA motor. I've been running no alternator for 14 years of racing, charging battery between rounds with no problem. However I've decided to add an alternator to speed up...

I've been toying with buying a spring tester. I'm going to know. I'm going to spend a little money and get a good one. I'm being educated. Thank you guys for your comments and help.

So using your equations I come up with different answers. [email protected] [email protected] 186/.55 = 338 lbs. [email protected] [email protected] 221/.60 = 368 lbs. Am I missing something?

The 120 seems too low for me as well. I'm confused about the 540lbs/in. Where is that?

So I'll add a little here. I bought a 360 crate motor from Mopar Performance about 16 years ago. It didn't have the special bolt with the hole in it for oiling. It also didn't have the 9/16 plugs in the block behind the plate. Look at some of the posts on this website and you'll see plenty...

This is the book that I have. It was edited by Larry Shepard. I'm not sure, but I think it might have superseded the book you have. Anyway see below. Thanks to both of you for your comments and such. Great info! I appreciate it. On page 203, this is what is said about the P2946353...

Interesting. MP performance book recommends these springs for this cam and others. When you say MP engine manual, I'm not familiar with that. Where'd you get it?

It's a solid flat tappet. Where did you get those spec's?

I've been going through my old posts and updating them. I installed that Lunati cam, lifter, spring, kit in November of 2013. It's first hit at the track was the Thanksgiving race at Las Vegas. It was a disaster. It bent several pushrods and destroyed 2 rockers. I had checked for clearance...

It's been a long time since I first posted my question. Well... I've finally installed the cam in the engine and taken it to the track. It was installed straight up. Ran a 10.95 in a head wind letting off the throttle in Phoenix. I haven't been able to race since due to the COVID-19...

Does anyone know if a quick change timing cover is made for the LA engine?

A set of 16? What do you want for them?

I need at least one W2 head exhaust valve. Part# P5249197. It's a 1.60" valve 5.29" long. I'll buy all you have. I'll also buy 2.02" intakes, part # P5249195, but I need an exhaust valve immediately! Thanks! Tim

I need 16 of part # P2946353 Mopar Performance Parts valve springs. Tim

Say 5"? What Back spaces do you have? Do you have any fronts in a 4.5 pattern around 3.5" or 4" width?

Centerline Autodrag wheels, 15 X 10 with 4.5" bolt pattern. Need 2 please. Tim

Oh yeah, car weighs 3,180 with me in it. I also always degree any cam I put in for accuracy.

So for all here is my current combo. .030 over 360. W2 (long valve) small chamber (57cc) mildly ported heads with Crane W2 roller rocker setup. Mopar 557 cam at present, straight up. Had pushrods custom made for length to determine proper rocker and tip geometry. Will do so for the 590 cam...

For anyone that has used the Mopar .590 cam in a small block. Did you install it straight up, advanced or retarded? I have heard that this cam works well with a 6 degree retard.