Search results for query: *

yea i saw that! i may have to try my luck there but they didnt seems to have the fronts.

thanks so much for the link

Hey All! Im having a bit of trouble locating Drums and Shoes for my dads car. I searched here before posting and checked out all the popular spots. (RockAuto, Ebay, Classic Industries) This has 10" Drums Im going to replace both rear axle seals soon and want to replace the old tired brakes...

It appears to be a non-Cap car

I do have vacuum there at Idle, I will check the routing. Its a "new" (refurbished) carb.

thanks so much for all this. i appreciate you

thanks , I did add washers but probably best to double up. The machinist is in the family and he said he didnt take much off, i wish i knew how much. Still got enough thread to add those washers which is helpful.

I knew you dudes had a keen eye for such details hehe. I seriously havent found such a helpful community before, usually just a bunch of "tough guys" in other communities haha

YES! I told my dad the same thing, we are snipping that this weekend! thanks

I thought similar, we recently got it new and my dad told me it was a mopar part

Im sorry, Do you mean to say "UNplug" while checking? I have been unplugging the advance.

This was something i was thinking of doing asap, just to be 100% sure that balancer did not slip.

Thanks, thats one area I admittedly have been neglecting. I may go get one of those bottom tap sets later today.

You are super helpful on this entire forum! The TDC mark seems to be the only mark I can make out. The manual i think keeps referring to "BTC" but it doesnt exactly specify on the rusted plate which mark is 5-7degrees before/after TDC. Im sorry if I seem ignorant. I do have mechanical...

I really appreciate your reply. I had not thought of that. I am going to check this today.

Hey all! I have searched for a while, not sure I am using the correct keywords. I cannot seem to get this car timed correctly. the timing marks are quite rusty and I cant seem to find it in our shop manual. THESE PICTURES ARE WITH THE TIMING LIGHT AND THE CAR RUNNING. This picture shows the...

Hey all! You all have been a huge help. I ended up getting the factory manifold milled flat at a machine shop. The Housing still leaks a very tiny bit. Funny thing, when i took the new housing off (after i found how bad it was leaking when i made this post), the housing was warped. I filed that...

thanks a lot for this, i got the factory intake milled and its still seeping a little. Im thinking something else is up here.

Awesome, thanks so much. I was wondering if there was a silicone / rubber gasket. I really appreciate it.

thank you

Thanks a lot

As suggested, here are some photos

Thanks for the reply! We have been through 4 housings in the past 2 years. It has leaked since we got the car a couple years ago. When we removed the first housing, there was a ton of corrosion on both the mating surface of the housing and the manifold. There is a bunch of pitting and no...

Hello dudes! I am having a hard time finding a replacement intake manifold for our 66 Barracuda. 273 2bbl. I saw a couple threads mentioning a few including the Edelbrock LD4B manifold, but that doesnt appear to be a direct swap. I like the thought of upgrading, but were are trying to remedy a...

Hey everyone! The issue was with the vent window Pivot Pin. The pin was snapped inside of the Pivot clamp. We found a Used OE replacement on ebay for pretty cheap. I just replaced the window and greased the pin and adjusted the clamp. I assume this could also be repaired with JB Weld and...

Awesome, thanks! the more that i look at it, it may be an easier task than what I first thought. Im glad that pivot joint has a retaining screw at the bottom

super good idea thanks! I didnt think there would be a fastener down there, i thought it would just have been a hollow bore.

Im ready to pull it out, it doesnt look like too much of a pain. Perhaps its a bushing or some new seals that could firm it up a bit.

Hello all! We have a passenger Vent window that is loose and constantly closing. I searched the forums and could not find any info. Is there an adjustment for this? Thanks Matt