Search results for query: *

Looking for a 68-72 slant sux K frame if anybody has a straight one they plan to scrap because they are doing a V8 swap. I would be interested in it. Thanks Matt

Looking for two 1&5/8" brass freeze plugs. Located in west Texas Thanks Matt

Looking for PN# 3743859 A833 OD trans aluminum bellhousing. Located in Abilene, Tx. All threaded holes need to be decent shape. Thanks Matt

Wanted 68-69 cuda coupe window regulator roller assy. This is the bolt on roller piece that bolts onto the die cast regulator piece for the quarter window. Need the bolt on one that the small rollers are not frozen. Tight turning is ok, I can free them up. I broke this one trying to unstick...

Looking for a 70 E body floor shift mechanism. Only need the shifter part with the gates. Dont need top plate or knob. Let me know whatcha got. Thanks Matt

Looking for a worn out set of 73-76 A body disc brake lower ball joints to temp assemble a vehicle so I can move it. I have everything else to temp assemble a front end under it. I just need the ball joints. They can be shot, and removed as part of your rebuild. I just need em to be able to push...

Looking for a small block 6 bolt neutral balance flywheel thats so worn and heat cracked it cannot be resurfaced, and a small block bellhousing in either aluminum or cast that's cracked or damaged where it cannot be used on a vehicle. Basically junk pieces. I am wanting to put together an engine...

Looking for a decent used OEM 318 center sump oil pan that fits 67-76 A body. Need something that's not dented up or rusty inside. Minor surface rust on the outside that's sand blastabale is ok. No stripped drain plug threads. Located in Abilene Tx 79606 Thanks Matt

Looking for a non A/C control section of an A body rallye dash plastic bezel. The rest of the bezel can be broken, drilled into, or otherwise destroyed. I dont need lens bezels, or any of that. Paint can be missing off this area, but raised plastic lettering must be in good repaint able...

Need 4 leaf spring shackle bushings. Poly or rubber, it does not matter. It's for a mock up. Thanks Matt

Looking for a 67-76 A body lower radiator support. Need something that's not bent to ****, rusted through, or cut into. I'm located in west Texas. I typically do paypal. Thanks Matt

Need 1 pair of SBP steelies. Nothing real good, just something that will hold air that I can put crappy tires on to roll vehicles around. Would prefer something close by where i am at. Located in Abilene Tx

Need 1 pair of SBP steelies. Nothing real good, just something that will hold air that I can put crappy tires on to roll vehicles around. Would prefer something close by where i am at. Located in Abilene Tx

Hi everybody, I am looking for some specific fender hardware. Namely a bunch of different thickness shim washers for the bottom of the fenders, and at the cowl where they attach to the body. I also need 8 of the fender mount studs that go in these areas along with the sems nuts, and CIP nuts. I...

67-69 barracuda notchback drivers side and passenger side complete side trunk drip rails, and section of the top of the quarter panels. Need pieces that are not bubbled to **** with rust since that is what i am dealing with now. I need them cut past the front and rear seams as shown in pic...

Looking for a stock aluminum water neck/thermostat housing thats not corroded all to crap. Minor pitting issues that are not in the gasket or hose areas are ok. Thanks Matt

Needed 70 - 74 318 2bbl choke heater cup tin that goes under the choke spring, and its gasket that fits in the intake manifold. See my pic below circled where it goes. Slant 6 is different, wont work. Thanks Matt

WTB pair of 67-69 barracuda trunk extensions. Looking for rust free and unmodified parts. I'm located in west Texas. Thanks Matt

Looking for a pair of rust free outer wheel houses from 70-76 duster, 71, 72 demon or 73-76 dart sport. Thanks Matt

WTB 2 speed wiper knob for small diameter switch shaft. Fits from 68-71 A body. Want something with good decent chrome on it. Thanks Matt

Looking for a 69 A body console shift indicator stub harness. I have the longer orange wire that comes from the fuse box. Need the short wire with the bulb socket and ground. Thanks Matt

Wanted: Working 69 up rallye dash tach in good shape with wiring sub harness if possible. Thanks Matt

Looking for only the drivers side A body 68/69 bucket seat without headrest. I have passenger seat, and all the tracks. Just looking for a drivers side seat no tracks. Anybody have an oddball single seat from these years they want to sell? Can anybody tell me, are the seat frames the same as...

Looking for a used weiand action plus intake. Something not modified. Also looking for an edelbrock 600 carb. Preferrably elect choke Locatrd in Texas Thanks Matt

Looking for this 1 part. A shifter lever for B&M automatic shifter for A727 A904 its the same install kit for most of their automatics. Dont really want to buy an entire install kit for it. Anybody have one of these they are willing to sell me. Maybe put in a padded mailer and send to Texas...

WTB 68-69 barracuda notchback upper rear window mouldings. I have the lower ones, just need the 2 upper ones. If you have only one of the uppers i would be interested in that too. I may have parts to trade. I have some misc 67-69 barracuda parts i will not be using. LMK whatcha got, and whatcha...

Looking for a decent used 67-76 trunk floor with no holes, or rusted out spare tire well.

Anybody have a rebuildable V8 A904 short tailshaft trans in West Texas Abilene area they just want to get rid of. I need one complete from flexplate back. I am willing to drive 75 miles one way to pick up. Thanks Matt

Hi Y'all, I am looking for a 67-69 stock square box type points voltage regulator. I dont need a good one. I need a burnt out one that i can gut out, and restore the cover and the base. I have an internally regulated denso alternator, and want to turn this into essentially a jumper wire so it...

WTB or equal or partial trade for a good set of 69 barracuda taillight housings and lenses. I have a bunch of parts to trade. Enquire with your needs. Thanks Matt