Search results for query: *

anybody know what types these are? top one says prothane, bottom one says HM softpack.Thank you for your time. RR

how do I fill the tank completely without it spilling out on the fender? Also anyone have a link to the neoprene bushing adapter going into the filler neck to reduce the hole to fit modern pump nozzles? thank you for your time. RR

63 dart 360. (273 64-66 V8 mts). On which side(s) do the tall/short ones go? I am way too high on the pass side (508 rubber insulators both sides). maybe I have the eng off sideways with the mtr mt slotted hole(s) in the kmember allowing alot of leeway for positioning side to side. thank you for...

are drivers & passenger side mounts the same height? and do you have any part #'s for em? thank you for your time. RR

63 dart stock car. 360 SB. what is the best flowing ex manifold to search for? has a thin shaft aftermarket steering column. thank you for your time. RR

63 dart was a /6. has the 3 mounting holes in the firewall roughly in a triangle. will a 64-66 A body V8 throttle bracket/cable bolt into the same holes? thank you for your time. RR

63 dart 360 in OE location. i had drilled the firewall for 2 holes for a later A body pedal/throttle cable but it is way to long. I found some cables on Ebay but they appear to be too long. I thought about shortening the cable I have & recrimping everything but I dont think that is doable. any...

'66 dart 360/904 stock car with aftermarket thin shaft steering column. Is there any way to lower the engine and or kmember to get my driveline angle right. I have raised the engine a bit & slotted the bolt holes/lowered the steering box so the magnum ex manifold on the dr side would clear the...

I am wanting to add a scallop to the other side of the crossmember so the dual exhaust will tuck up nicely. I have an extra crossmember. should I cutout a scallop then weld in some material or cut em both in two & weld the 2 good halves together and should I have it mounted in place for dead on...

where can I purchase one, to reduce filler neck ID to match thin gas pump nozzles. thank you for your time. RR

having starter to a swapped different ex manifold clearance issue. I under stand that the super compact mini starter from a 2007 dodge ram with a 5.7L MANUAL TRANS is what I need. how do I ID it so I can make sure the yard is selling me the right one? thank you for your time.

63 dart 360/904. the custom ex pipe down from the ex manifold that I want to go with is too close to the starter body. how much skinnier is a mini starter? Stock car & no ex wrap is allowed. and is their a starter wrap or heat shield for this. thank you for your time. RR

the thick "brick" ones with the 2 metal "lips" opposite of each other OR a thinner set/no lips that I see on Ebay listed for 64-66 A body 273? Thank you for your time. RR EDIT I reread the thinner ones descrip & it says for 64-69, not 64-66 if that makes a difference.

does anyone have a part # for these, iirc it was for a 1990 dodge D250 diesel. thank you for your time. RR

how much of a job is it to add air conditioning to a non air car (65 dart)?. at home or a pro shop handle it? R12 or 134A ?. thank you for your time. RR

what is a good/stout/long lasting brand to get (part #'s appreciated). thank you for your time. RR

considering a set. is there a tire dia limit to be aware of/other potential interference areas? thank you for your time. RR

what are the best ones that fit & flow the best? thank you for your time. RR

1963 dart. what are the front & rear brake shoe diameters/widths? (9" on the dia I would assume). thank you for your time.

63 dart/63 kmember/64-66 A 273 mts (with the tab welded on one for a 360). Which black insulators should I use? the thin ones listed for a 64 V8 or the thick ones for the 63 slant 6. racing app & I do have the one mentioned further down, the one for the drivers side with the interlocking tabs...

they have a 1/2" stud on one side & (2) 3/8 fine thread studs on the other side. what yr/make did these come from? Thank you for your time.

next years' 63 dart stock car, I will be purchasing the widest radiator that will fit (side to side). Thank you for your time.

A local guy on CL has a new rad for a 92-94 jeep grand cherokee/92-3 grand wagoner V8 for cheap ($75). I was thinking some had said that this is a good fit/choice on an early A body. Thank you for your time. RR