Search results for query: *

your still ahead of me! Keep it up.

The shorted line is actually under the bottom plate but it will burn right at the entry point and you need to get in there to properly splice it.

HP04 oscillating fan with heater function and air filters. Its the weird Edsel grill looking fans for home use. If you can find one with no power , smell the bottom plate where the power cord goes in for burn odor. If you can smell burned plastic or rubber, the cord where it bends for the...

Static tire balancer, make some mandrel for hub size and center cap of your rim and buy a bullseye level. Center the golf cleat and set into cup of pushrod. Stack pennies on edge to balance. Weigh the stacks and apply the stick/clamp on weights and check for bubble up. Worked better than a...

I had an old 24v 500w mower that would bog hard on basic grass, i hope they got better. I took the motor out and put it in my kids Razor scooter, it rips at twice the rpm of the old 250w motor.

Would work on larger ones, novel idea! Span one wrench over side of nipple and then hook it with another and pull across the part. Nipple may slightly crush and break free.

I save pretty much every PCB and rechargeable battery pack I come across out of scrap electronics and spend leisurely hours in the garage with the stereo on, heat gun going and pliers pulling out anything that will come out of those boards component wise. I got a pretty good collection of...

post 32, 50, 56 and maybe 60 are the only SS pics? Yeah, that shows they are not really that popular. I see quite a few Radirs , torque thrusts, and other non chrome 5 spoke that look much better than the thick 14 cragar SS's. I like the satin Centerlines for a modded look and the Rallyes for...

All those pennies balanced it and that was with the original weights on from a previous dynamic balance. I must have lost some weights as it was smooth for about a day and then started flaring up at 55-63 mph and would smooth out past that. I stripped all the old weights off it and got it down...

Made a centering puck for the bottom (3D printed the OD of the raised centering boss of the hub) and a bullseye pad for the top that sets into the recess for the center cap. Bottom has a 3/8 drilled hole centered for a screw in golf cleat, wrap with pipe tape to get a snug fit. I sharpened the...

Dawn Wells...or Raquel Welch! It just wouldn't be the same if Raquel got the gig......

Positive ID on German one....."OLD GERMAN MAUSER BAYONET /SCABBARD MOD95 --SOLINGEN MADE" "...pre-WW1 German Wooden gripped M.1895 Mauser Bayonets, each --------with German Maker's details on the reverse side: WEYERSBERG KIRSCHBAUM & CO. SOLINGEN." This was from a Ebay item that had some Chilean...

Oops, the German ones font looks too good to be old...? But all the grips look original eroded wood

Friend found a hoard of knives pre estate sale from a deceased relative. They said take the whole lot and it was about 500 various China replica swords, machetes, multi-tools, combat knives....90% Chinese made trinkets. I saved these 3 original looking bayonettes from a $100 valued pawn shop...

But none of the intake based bungs have line of sight to the back of the valve. Only really an issue when your counting % of HC at the tail pipe as in smog regs. That's why TBI moved to MPFI , just emissions. Anything efi with an O2 feedback is better than a 1920 or a BBS, even in good tune.

you could get real trick and run the fuel cell mounted on a scale, just keep and eye on the weight remotely...aircraft style. "I got 35 lbs, Im good!"

how about running a fuel flow meter and just keeping an eye on it? 15 gallons flows 15 gallons. When the meter has flowed 13 gallons time for a fill up and a reset. No sure how much these are but this one is $35. It may measure way too much like 1-60 liters per minute...

Dutra sold to Clifford, and then sold dutra duals to Australia....Spitfire sold out to Laysons..Im sure everyones getting royalties.

Huh? Never mentioned crank gears......But I do have a Milodon gear drive with a crank gear... ?

did they do the A/C-non A/C fin count change? Ive seen so many rigged Mopar pulleys with spacers you'd think it was stock.

its illegal on the strip but other than that, sounds like a winner! That Dex-cool about ruined my Suburban. Going on a multi state road trip and we pull into an Albuquerque service station running a little hot. Right as I'm about to pop the hood, the stat housing blows out and dex cool shoots...

with gask-a-cinch......? How about AL spray paint on copper head gaskets? I dont see any issues unless its a sliding gasket face like on a slant exhaust manifold or the bottom of a head that takes a certain RA so the MLS gasket bites OR slides.

Ive seen oil drive hex worn almost round and all that torque runs through that keyway. Had SG rear axle splines twist almost a full spline right out of the carrier, stuff happens.

I used a Magnum nipple and adapter plate on a 360, worked. Some say you have to bend the plate a little for it to seal but Mine sealed fine.

The water store on the corner has spigots where you fill your 5 gallon bottles under. They used both hot and cold valves so they turn on left and right!

Supposed to be a heavier stamping in the 340/360 but that was debunked once. But they are the same dimensions.

Bought 2 front loader washer/dryer combo. $200 as they washer "leaked" and the dryer did not match the new models. The "leak" was a rubber 90 on the top that a rat had chewed through. I just muscled the hose around the corner and its still going strong, its a newer design but goes to show you...

We had a 1955 5 pilot light oven with a griddle, gas man says it was drawing about $350/yr on pilot light alone. I should have just lit the damn burners myself as it was really a neat old oven. The griddle was awesome as well as the little matching salt.and pepper shakers outboard of the built...

I bought a 1981 Coleman gas generator just for the 5HP Tecumseh green painted motor for my 1968 Powell minibike, paid $50 for it on facebook. Motor probably had 1 hour on it as the exhaust was still painted! Took it to a buddy who had a lathe and he turned down the tapered shaft to a 3/4 shaft...

PPG Ditzler paint codes 55-65 Chrysler Take it up 500% (CRTL +++++++++) http://www.jholst.net/paint-codes/paint-code.pdf