Search results for query: *

Got one and of course you take it apart before you install it right? Redline (only importer of Weber carbs in USA) says set the float to: 18mm from top of float off the gasket with the needles spring ball barely touching. Then Pegasus racing say "...Weber recommends setting the height of a...

Not Slant specific but applies to all guide installs: What's the stem to guide clearance on a .315 (8mm) valve stem? I'm using a bronze guide and once I pressed it in, I need to ream it and I don't quite know what the spec is for the ID of the guide. In the FSM is says 0.315 +.0018/+.0010. Is...

How long does it take? stock Iron rings, 240 grit dingle ball clean up to uniform gray on parallel glazed cylinders. procedure? Just on my beater Mazda.

Nice youtube vid of a slant mill getting a 1bbl sniper.

Mao's version of a Holley 1904-1920 1bbl. Who's gonna try one? $89 shipped for a NEW casting...May not be that bad, I've had good results with Chinese carbs 1 Barrel Carburetor REPL HOLLEY 1904 1908 1909 1920 Fit For Ford 6CYL Engine | eBay

drained 6 quarts of chocolate milk from a 4 quart oil sump. Motor only ran about 10 minutes at about 700-1000 RPM. Im guessing 2 of those quarts were distilled water (coolant). Did I fubar the bearings? I was trying to diagnose a terrible miss, the back two of 4 cylinders have intake ports that...

Napa 9168 double roller slant chain (use S338, S339 cogs) also fits a Vette, and alot of other stuff! https://www.napaonline.com/en/p/MOG9168?impressionRank=3 Hit 'buyers guide'. I knew of the B/RB lineage but not the Ford/Chevy/GMC link!

Interesting balance video of a straight six crankshaft. The shaft itself is balanced to itself, not the reciprocating parts as they are their own counterweights as long as they are all the same weight. No need for the reciprocating weight when balancing a straight six crankshaft, each rod...

Not slant but four banger related. 82 Mazda 2.0 knocks on acceleration under med load. I dont remember it doing this but its been OOS for a few years. I had the head resurfaced and they had to take like 30 thou off as it was heavily pitted. in doing that it raised the compression x amount of...

timing set stats.... Slant Six..................... 5.125 -1.5640- 0.7500 -2.0020 -25/50 -3DR66-2 Chrysler BB Triple Bolt ..5.125 -1.5640 -0.7500 -2.0020 -25/50- 3DR66-2 Same timing chains used. Just food for thought when you cant seem to find a good slant timing chain. (center line...

I get these from time to time... Standard Motor Products V180 push in PVC valve... .98 cents! CHRYSLER 1960-1969 DODGE 1961-1969 Melling solid 'Dumb bell' lifters, $1.82 (4 left) Sealed power or Clevite rod bearings, <$3.81/pc. (slant) Wholesaler Closeout Parts : 1968 DODGE A100 3.7L...

Clifford, offy, Hurricane, Dutra Hyper-Pak repop? Heat or no heat? Testing the waters for the most popular, cost not really a factor. More interested in design concensus. Offy had long stock looking runners, Clifford had shorter runners with a larger plenum. Aussiespeed Hurricane had crazy...

Took forever but here it is. Fuel Injection Slant Six Chrysler/Dodge/Plymouth 225/170/198 Intake Manifold Kit | eBay Not the price point I was hoping for but this opens the door for a few rich slants to be injected off the shelf.

Big ends were wider on the forged crank rods..who knew? @6:50

Anyone got a pic of an early (1960?) driver side alternator mount. Maybe trucks had them too?

why not?

where can I get one like this? seems a way better place to hang this than out in right field! Modded PS mount?

I got some used solid Hemi rollers and wondered if they could be used in a slant if I made the correct length link bars. Have Oregon cam grind me a roller (if they could as the roller lobes are super skinny) ..no hydro adaptation needed. Same diameter....?

I got this blast from the past in the mail today But the gear pin hole is too high, does it matter or is there a proper clearance for the end play of the shaft? There is like 3mm of difference in the spring-pin holes. Do I cross drill the gear to match the old hole level and retain the old...

I fashioned this out of EMT, a piece of plate metal and an old Edelbrock cast valve cover. I bought the flanges off Ebay. I made the runners as long as the original Ramchargers formula for intake valve timing off a stock camshaft, I think it was around 240 degrees. I picked the 4th or 5th wave...

I bought a aftermarket cam off this board years ago and totally forgot the part number. I installed it (a year ago) and now am wondering WTF I installed! I know it was a mechanical as I got 11 solid lifters with it, but I dont know the grind. My only clues are the installed valve lift (mic'd off...

This was a tough one but I managed. Pulling it was the normal procedure: thread 3 bolts and run the jackscrew into the crank end with an appropriate non-damaging tip. Run a breaker bar between 2 of the bolts and run it over to the frame rail to hold crankshaft. Now getting the **** on is another...

what is the signifigance of the colored link on the non roller timing chain? Do you count the links to the dot like other colored link chains? Where is the info, I got the chain out of the box. I know you line the dots up but I think the colored link is a more accurate way to set it when you are...

65 Barracuda, you can swap the cam without pulling the motor. You do need to remove the radiator and the right bumper mount (and loosen the left) and both motor mounts. Lay the motor pan rail on the K with no motor mounts and pull cam out until it hits the lower bumper lip. Then determine how...

What a *****! My 65 had to have both its motor mounts removed (per FSM) then I had to put a scissor jack between the block and the frame rail and pry motor over about 6 inches while floor jacking the motor until it hit the firewall. The FSM says you can do it with a piece of wood wedged between...

or was it only a 1959 press release pencil drawing?

Can you reuse these? Guys reuse copper ones, just never thought it through.

is there a trick on mouinting the new timing chain cover with new rubber oil gasket on a motor that has the pan still attached? Thought you could slide it in there and tighten but Im having a heck of a time. dropping the pan on a 65 is tough.

Sounds like a joke, eh? Well, its not ... 1. There is no bolt boss by the thermostat housing for the "passenger side" alternator tensioner. 2. There is no bolt boss next to the #1 plug hole for the 3 bolt alternator base to bolt up to. 3. There is no "countersink" machined into the face of the...

Sort of off topic but i got a 4cyl carb motor (just think of it as a low po 6 with 2 less cylinders for this question) and i have some serious blowby coming out of the valce cover filler hole. Its enought to float a ping pong ball on! Im wonderi g how much is about average? Have not done a...