Search results for query: *

Just picked up a 7 1/4” with a Dana clutch sure grip. Strange thing is it has a 3.90 ring and pinion. Was this very common?

Came out of a 73 Duster BBP 10 bolt cover but it is not oval like a 8 1/4”. It has 10x2 1/2” brakes and C clip axles.

I have a truck housing that I want to shorten to stock A body width. Now I know a stock A body width is 52 5/8”. But I need help on what the left and right axle tubes should be to have the right center offset. My first attempt at shortening a Dana 60 truck housing. I have a set of 3.54 and 4.10...

More specifically, will a standard shift flywheel off a 1972 340 work on a 360? Is the balance the same?

I couldn't find after searching for info. Any one have a good web page that lists this info? I have a SB 727 that was behind a 71 340. Not sure if it is original or not. Number is pk3681862 4483 7158

Been a long while since I rebuilt one. Are the bolts holding the cases together left or right hand? I know on the 8 3/4 Dana power-lok are left hand thread. I think the Dana 60 model are right hand thread.

This is the numbers I got off of it right above the trans pan on drivers side. Trying to determine what year it is. PK4058302 6123 8342 Thanks

Does anyone make a sleeve for mopar yoke?

I posted this question on FTO. But it's a ghost town over there! I just acquired a 97 SB Dakota ( was a 4 cylinder) and the previous owner welded the spiders! So I'm looking for a Sure Grip unit for it but was wondering how many spline axles it has? I'll have to tear it down to verify it. I...

Over the many years I've played with cars, today I think was the biggest screw up ever! I decided to install the Turbo Action Cheetah shifter in the 68 Barracuda today. So I locate where I want to mount it on the floor and where the cable needs to exit the floor. I used a 7/8" hole saw and...

Ok , so I go to install the Cope Racing 727transmission in the 416 68 Barracuda and discovered another snafu. On the drivers side lower 7/16 bolt that bolts the block and trans together, there is no hole in the transmission where the bolt that is suppose to go from the front of the engine into...

Can someone verify that the correct National Seal part number for a 1971 7 1/4" Axle shaft seal is a 8660S?

Maybe someone here can clear up an issue with these damn 8 1/4 rear ends. I know there is a different carrier for different gear ratios. But I have a Mopar SG part number 18-05-039-903 that I tried to use with a new set of 3.55 MP gears. Well the carrier winds up to far away from the pinion. Ok...

So here is the st6ory. I buy some parts from a guy not real far from me. In all this stuff, I buy is a 8 1/4 rear that I was told came out of a 73 Duster 340 car. But here is where it gets a little weird. It's definitely is a 8 1/4, the casting number is 2852905, the spring perches are 43" apart...

I need two spider gears for a 8 3/4 Dana power lock clutch style sure grip. Two of the four spiders are bad. Anyone have a couple for sale or know who sells them new?

I know I should post this on the truck forum but there are more members here that might be able to help me out. I have a 95 2500 Dodge ram with a V10 that I need a transfer case for but I can't located one. My question is shouldn't I be able to use one out of a 1/2 ton or Durango? I know the...

Ok here is the story. I bought a real nice all original 1990 Ram 150 2wd club cab, 318, 4speed. Well I put a new set of Goodyear Wrangler tires on it and took it for my first drive and it had a bad driveline vibration between 35-60 and then it gets less obvious. I pulled the 2 piece drive...

I'm looking for a trans that will work for the 67 GTS 383 Dart I'm building. I need to find out the date codes for these two BB 727's First part number is 2466900 numbers on the rail are H22538334 2862390 And is marked a 66 Second one part munber is 2466900 number on the pan rail is...

I wound up with a 9" 727 convertor but I can't see any part numbers on it. Is there a member that builds convertors? I'd like to have this one gone thru and made to my specs.

I want to make sure I'm on the right track. I can run a neutral balance converter on a 74 360 external balanced as long as I use the special flexplate like the the 10236 B & M right?

I know this was answered in the past but I can't find the thread. Who sells the filter extension for a 727. I have a deep aluminum pan but no extension. Thanks

I need the special flex plate to use a neutral balance torque converter in my 727 360. Any body have one? Or can tell me the B & M part number I need?

I just bought a bunch of linkage pieces. They are not A-body for sure. Anyone know how to ID these as to what they came off of? Web site or literature?