Search results for query: *

Well, my governor decided to come apart and knock a hole in the extension housing. I have the TransGo TF-3 kit installed. Would it be okay to leave the valves out and replace the housing with no issues?

I'm looking to purchase a good converter while I'm in the process of this swap. Will a 2800-3000 or 3000-3200 be too much for a little daily driven 318 with a TF 727? I have a 750 Edelbrock, Weiand Action+Plus Intake, Exhaust, Mallory Ignition, Electric Pump/Fan, and 3.55 gears. I do plan on...

I was wondering if anyone knew what size bolts are required for the brackets that run from the engine to the transmission.

I just installed my A-500 and Reverse wants to play Hide and Seek. The forward gears are fine. I put it in Reverse and you can hear the transmission engage, but will barely move or catch and begin to move. Other times it acts like it's in Neutral. I want to inspect and clean the valvebody and...

I'm in the process of rebuilding my A500. I'm having issues with the kickdown band fitting properly around the drum. I normally get parts from WIT, but I ordered the band from O'Reilly's(Part # 767021). The band seems to be smaller. The adjusting screw will not sit in the grove of the band. Has...

Hi, I'm in the need of a tail housing and searched eBay. I found a few late style housings. My question: Will the early and late style extension housing interchange with no issues? Thanks in advance! Joe

I had an issue with my 2-3 gear shift. It would do fine under normal driving conditions until operating temperature... Then, it would slip or seem like third gear is not fully engaged unless you get off the throttle, shift, back on the throttle (same result under full throttle). It also had an...

I recently installed my transmission and there is a lot of slippage in 1st and 2nd gear with no 3rd gear. It will go in reverse, but there is a lot slippage identical to 1st and 2nd gear. Could there be a blockage in the valve body that would cause these issues? I've adjusted the bands more than...

My washer/cup that goes on the end of the output shaft decided to grow legs and go on a permanent vacation. I've been searching high and low, but no luck :banghead: I guess I'll have to order them from WIT. On the website, they're showing three sizes (.052, .068, and .083). What is the correct...

I'm in the process of ordering the forward planetary gears for my lockup transmission. WIT has them in stock that uses the 5" OD Ring Gear. Would that be the correct part to order? Also found one on eBay with the same description... http://www.ebay.com/itm/like/291296046587?lpid=82 Part...

I currently have my transmission apart (broken converter hub) and was wondering if I needed to replace the band while I'm in there. I never had any issues out of it. I do have a manual valve body installed. I wanna make sure before I put it back together. What are some symptoms of a worn...

What's the proper forward clutch thickness for the A904/A999 transmission? I'm seeing 0.68" and 0.61" on two different sites.

I've done numerous searches, but nothing really gave me the information needed. I have my A904 transmission out fixing converter and pump issues. Sounds simple right? About a year ago, I decided that I needed a manual valve body in order to have the correct pressure since I couldn't hook up...

My front pump is trashed due to converter failure. I've searched local junkyards for one, but nothing came up. I searched online and found one at GatorTranz in Tampa, FL. They have the early style and double bushing style... Question: Being that my transmission is an 84 model, does the front...

I've been some research online trying to determine if I have the low-gear in my transmission. From what I read, all lockup versions came with the 2.74 low-gear and the non-lockup came with the standard 2.45/1.45 set until a certain year. 4295887 8450 3642 (I see a P and what seems to be a...

I need to order a kickdown kit for my 904 (318 with Edelbrock). I came across a PDF file showing how the Lokar kit needs to be installed. It seems like the bracket & lever kit for my shifter will be in the way. Has anyone installed the Lokar kit with a shifter cable...

I've been browsing around for a rebuild kit for my transmission and I'm curious about the clutch colors. The transmission will see the track on occasions, but mostly driven on the street daily. The transmission has a B&M Shift Kit installed already. What would be a good kit (that won't put a...

I have a transmission that came out of a '72 Dodge D100 laying to the side. I picked up a TF-727 (already installed in vehicle) a few weeks back, but do not know what it come out of. I want to take the valve body from the one I have laying around and install a B&M shift kit. Then, I would swap...

Last night, I experienced the almighty stuck converter. Today, I asked around to see what was going on and how to solve that problem. After some hard work, it came out along with something extra. My question is where does that bushing/bearing fit? Does the front pump have to come off?

I need to purchase a Rear Servo for a TF-727 and was wondering what was needed for the fix. Do I just purchase the piston alone or ??? Browsed eBay... http://www.ebay.com/itm/TORQUEFLITE-727-Low-Reverse-Band-Servo-Piston-1974-/370390861813#vi-content Browsed Google... Transmission Parts...

The reverse in my transmission decided to take a nap. I never had much of an issue before this matter. I can put it in reverse or neutral with engine off and push it back... With engine running, seems like everything is engaged/shifted forward for the drive position. I can put in reverse/neutral...