Search results for query: *

Looking for a can or two of P4120752AB turquoise engine paint. I would even consider partial cans as I am just a little short of finishing my engine re-paint. Shipped to SD zip 57004.

Looking for a good thermostat housing, used from 1957 to 1966 on non A/C cars, part number 1855393. PM me if you have one available, thanks FABO. Pic for reference:

I seem to have misplaced mine, anybody have an extra laying around?

Looking for the large .043" pump nozzle for a Carter AFB carb. I don't need the three piece kit from Edelbrock (.024", .033", .043"), so hoping someone has the large size nozzle they are not using. Please PM me if you have one available. Thanks!

ISO factory black dash vents for 68 Barracuda. Bad experience with repops so want factory originals in great shape. Thanks FABO

Looking for 15-20 door panel clips, as pictured, for a 68 Barracuda. I do not want the wire type, and would prefer used OEM over aftermarket with the correct foam still on the clip. Any one have extras laying around from previous parts cars?

Long shot search - Looking for a 383 2bbl intake, casting number 2843681, cast date prior to August 4, 1967. For my Sport Satellite, not an A-body. Thanks.

Looking for a decent set of defrost vent tubes for 67-69 non-AC car. Looking for OEM style, good used is fine if no rips. I know repops are available but prefer originals. Hoping someone has a set laying around from a drag car, parts car, etc. Thanks!

Looking for the correct mounting nuts only for a 67/68 Barracuda delete plate.

Anybody have a good used set of black seat belts for bucket seat car? Would prefer date coded in August or September 1967 as car has build date of early October. Figure I would check for used before going with the refurbished option. PM me if you have any available.

Looking for 68 big block throttle return spring bracket, non A/C car. I know I can get reproduction; just checking to see if anyone has an extra one to spare.

I have one reproduction battery to use for a couple of cars when going to shows, so am in need of six green caps to be correct for one of my cars. Anybody have a dead/bad reproduction battery that has green caps? If it matters, the battery I have was purchased from Summit. Thanks FABO

Looking for the top only for a 68-69 unsilenced air cleaner. Don't need the bottom; just purchased one over the weekend. Thanks FABO.

Looking for a 39 tooth speedometer gear for my 68 Barracuda. I believe this one is dark green in color? Put a 38 tooth in and speedo reads just a little too fast. I know I can buy new but figured I would check here first if anyone has one lying around and wants to part with it! PM me price...

Building a bar top for the man cave, so I am looking for 6 to 10 emblems to countersink in pallet wood planks and cover with bar top epoxy. That being said, I am looking for low cost, bottom of the barrel type emblems that you would NOT want on a car. I have enough Barracuda stuff, so prefer...

Looking for a 68 Plymouth emblem to install in sport/wood grain steering wheel horn cap. I have a 69 Barracuda emblem to trade. Barracuda emblem has three small scratches as shown in the pic. Thanks FABO.

Want to upgrade one of my Barracudas to the wood grain steering wheel. Not looking for cracked one; plastic and spokes must be in good condition. Thanks FABO.

Looking for a 68/69 blue horn cap for a sport/wood grain steering wheel. Going in a 68 Barracuda. Thanks FABO.

Looking for a heavy duty over center spring for clutch pedal return on my 68 Barracuda 383 4 speed car. PM me if you have one available, ship to zip 57004. Thanks.

I am looking for a good OEM or NOS left (driver) side defrost vent hose. Measures approximately 25" long and is 2 1/4" diameter on end that attaches to heater box. This is for a 68 non A/C car. I would purchase both hoses if available. Picture shows the style/material I am looking for. Other...

Looking for the correct wiring harness for my 68 Barracuda 4 speed. I have the two wire connector coming out of the bulkhead connector in the engine compartment, so what I need is the wiring from this down to the single pole reverse light switch on the 833 transmission. PM me if you have...

I quit looking for this quite a while ago, after many months of searching. Then tonight I found one on Ebay that sold three months ago. Not happy with myself to say the least, so here we go again--- I am looking for an oil dipstick for an A-body 383 engine. Part number is 2899411...

Re-posting my previous wanted ad. I am still looking for a good left (driver) side defrost vent tube. Measures approximately 25" long, 2 1/4" diameter on end that attaches to heater box. Thought I had one that would work, but ended up too short. I have an NOS tube for the right side so...

Anybody have one of these vacuum nipple fittings? Manual brake car so looking for this special nipple to hook up performance indicator gauge. PM me if you have one.

This is what I am looking for, but in better condition. This picture makes mine look better than it is, deep gouges/scratches on edges and gouged on bottom edge in numerous places. PM me if you have one available. Thanks FABO.

I am in need of good condition, original style defrost vent tubes for my 68 Barracuda. I understand that 67-72 A-body, non A/C cars are a match for the style I need. Thanks to member SSBA, attached is a picture of the defrost tubes I am looking for. One is larger diameter than the other as...

Looking for two fender braces for 68 Barracuda. Braces that go from inner fenderwell to wheel opening lip. Looking for good metal, not all rusty and pitted. PM me if you have a set. Thanks FABO

Looking for a map light switch mounting nut. I don't need the bezel or the switch, just the nut. PM me if you have. Thanks FABO.

Thanks to confirming information from other members, I am re-posting this thread with updated information. Looking for an oil dipstick for an A-body 383 engine. Part number is 2899 411, and would be for 67-69 Darts and Barracudas with the correct 893 oil pan. I do NOT need the tube, just...

I am looking for a 383 oil dipstick for my 68 Formula S. Engine has the 893 oil pan. I don't know if they are different length from other 383's so here are the dimensions of what I am looking for, courtesy of member MOPARMITCH: Length from tip of dipstick to the insert stop lip on the handle...