Search results for query: *

I know this is a farily common mod, but I've found a nice '73 but dont care for those bumpers. Is it a big job to either replace them w/72 styles or even cut the big heavy bar our and bring the original bumper in closer- ie, remove that filler pan. How expensive would it be and is it worth the...

can the 1975 bumpers w/filler panels be changed for the older 70-72 style?

They are just behind the rear wheel, patch panel for quarter is OK, but would one just cut up some tin for that area behind that is AWOL?

I know many say they always crack if glassed on a steel hood, but what about riveting- is there a method where the rivet head could be countersunk and covered?

I have a fairly rust free '72 Duster but the passenger side lower quarter has some bubbles. This is NOT a show car and I do not want to cut and weld at this time, but again, I was told that if one could seal BOTH sides of the sheet metal that the rust process would slow down due to a lack of...

I made one temporarily and it actually looks fine- I found a used one very reasonable from another member, but this will give others an options vs buying a new one for $42 and shipping. I used an old truck inner tube to cut it out and the 3 mounting screws plus some adhesive around the edges...

What color- thinking they may have been left steel, but silver is close- not body color or black? 1972 Duster!

Its been a while since I have ordered stripes and I know venders come and go: what firm is recommended for both COST and quality- which should include decent instructions.

FOUND IT IN THE TRUNK! 1972 Duster- just guessing they were the same for the 3 yrs from 70-72. Confirmations?

My 72 Duster is pretty solid, but not rust free. Its not showy and thats what I wanted this time. Its had some moderate panel patches (lower quarter and taillight panel) and I see some minor bubbles forming on the rockers- mainly just behind the back of the door. My question is that I'd like to...

UPDATE: I just finished some research on this swap and have decided that I will most likely stay with the 71 tail panel- just too much money and trouble to switch back. With the tail panel shadow stripes, the two lights do not look that much different. I am in the process of buying a '72 had...

Dont think the Sharkstooth fits with that hood, but has anyone come up with something cool? Guessing one could fit a glass 6 pack style hood and then use the older generation grill?

Looking at a '73 but like the 70-72 grills better- especially the Sharkstooth. Will they bolt in a 73 or is the bumper area different. Can that be altered w/out too much trouble?

Thinking about using a glass bumper on my '68 front end, has anyone come up with a simple & Light, inexpensive bracket (homemade?)

Like spraying Rustoleum or POR15 into the A/B pillars and rockers? How could you attempt to clean inside/dry it out before?

Stock grill in the Valiant looks mighty similar, will the Duster sharkstooth fit correctly into the Valiant?

Discovered I am missing the drip/roof molding on the drivers side of my Duster. I assume these are side specific but wondered what years would work. Anyone have the part I need? George in Tallahassee

1972 Duster in FE5 BRIGHT RED, local jobber only has the formula for enamel and I need it for base/clear. They sell Dupont if that matters. Thanks, George in Tallahassee

There appears to be a larger gap between the bottom of the front edge of the hood and the top of the Sharkstooth grill. Is there supposed to be some sort of filler piece attached to the hood or even the top of the grill/latch area? THis car came with a pin on glass hood, so I am in the dark...

My scoop has been used and I am not satisfied with the holding power of the mounting screws that thread into plastic inserts in the fiberglas studs on the scoop. Was thinking about filling those studs with some sort of material that I could drill out to the correct size of the fasteners that I...

I believe I need it all, what A bodies and YEARS will work on this Duster? Thanks, [email protected]