Search results for query: *

I do not know how many of these clips there are to hold the stainless trim in place just below the rear window of the cargo area of my 68 barracuda fastback, I just know I don't have enough of them. One side has 6 and the other side only has 4 and there are a lot more holes than that. Does...

Does anyone have a nice black drivers side rear armrest with the ashtray for my 68 barracuda that they would like to trade for a nice passenger side? Here is the one I have for trade, there are no cracks or damage. Thanks Bob

If anyone has a parts car I am looking for the license light wire along with the grommet that hooks up to the license light itself and goes through the back panel to the trunk harness for my 68 barracuda. Mine was cut off right at the harness so if you can cut the wire right at the harness or...

I am in need of a driver's side front and a passenger side rear wheel lip molding, the other two are in good usable shape. If you have one or both of them in good usable shape without dents or scratches please let me know, and if you can please post some pictures and contact me with a price...

I am installing some of the cat whisker back on the 68 and when I got to the rear outer 1/4 window whiskers the passenger side top clip was broken off. Also the factory whiskers have two clips up there where as the replacement ones only have one clip. I am looking for three clips like these ones...

I am looking for two of these clips that hold on the rear trunk molding for my 68 barracuda, the ones with the two studs.

I am looking for one of these small block upper kick down rods in the pictures to use on my 66 273 4bbl, if you have one for sale let me know. Thanks Bob

I am looking for one nice black front arm rest and one nice black drivers side rear arm rest for my 68 barracuda fast back. I do not need the rear ash tray or the ash tray bezel just the arm rest it's self. I will also need them shipped to 48346 Michigan. Thanks Bob

So the release lever for my rear fold down seat back in my 68 Barracuda was on the very sloppy side, so I took the seat apart to see why. I found the release rod was bent, the nylon grommet was not in the correct hole, and the lever return spring is broken. Has anyone ever seen these re-popped...

The PO of my 68 barracuda fast back had cut the rear carpet strait across from under the rear seat leaving the sides of the rear seat bare. I am looking for two pieces a minimum of 10" long and 6" wide to cover the void. If any one has two pieces of black loop carpet or even a piece at least 20"...

I am looking for a set of cam's, bearings, and the set screws that hold the cam's to the bar for my 68 fastback barracuda rear fold down seat back. If you have them please let me know. Thanks Bob

Thought I would check to see if anyone had a new black console carpet strip for the automatic console in my 68 Barracuda they are looking to get rid of before I order one. Thanks Bob

I changed my 66 with a 273 from the 2bbl over to a 4bbl using the correct commando 4bbl intake and adding a 650 Holley, I have not been able to get the kick down to work since. I have seen the post with the different bell cranks from a 2bbl and the 4bbl and I do have the 2bbl bell crank mounted...

I am looking for 4 of the rear axle yoke strap bolts for the 8 3/4 rear end in my 68 barracuda. I have the straps I just need 4 bolts. Thanks Bob

I am looking for a drivers side trans to engine brace for my 68 barracuda with a 340 and a 727 trans, the one I am looking for is in the picture on the left side and I believe it is approximately 11" long. Thanks Bob

Looking for a Flaming River FR1506P steering coupler, If you have one to sell let me know. Thanks Bob

I am looking for a Flaming River FR1506P for my 68 Barracuda with power steering to clear the Headers. I have found a few on line but don't really want to give up my first born. If you have one and are not going to use it let me know. Thanks Bob

I am in need of one upper rear seat hinge bracket bolt. It's the one that holds the lock and un-lock plate to the side of the upper rear seat, the one with the release lever on my 68 barracuda. Look at the picture it's 1 1/2" long and has the letters SEMS on top of what looks like a large T and...

I finished rebuilding my 68 Barracuda A/C and heater assembly the other day so it was time to start on the dash assembly. While I was putting everything together I noticed that the heater resistor plug was a little melted and dis figured. These ends are used in a few more places on the dash...

I am looking for the rear air compressor mounting bracket and the two bolts that hold it to the compressor for my 68 Barracuda small block. Look at the pictures, this is the bracket that I am looking for. If you have one let me know along with shipping to 48346 Michigan. Thanks Bob

This 68 Barracuda is a factory A/C car and I have found just about everything that I need to put it back to original. The one piece of the puzzle that is missing is the heater hose valve that's mounted on the passenger side inner fender, I am told that it is not reproduced. My question is #1...

I am looking for the small inspection cover and bolts for a small block 727 dust shield. Please post a picture of what you have and PM me a price shipped to 48346 Michigan. This is what it looks like. Thanks Bob

Looking for the alternator brackets, spacers, and bolts for my 68 Barracuda 340, they don't have to be pretty I can blast and paint them my self. Please post a picture of what you have and PM me with a price plus shipping to 48346. This is what they look like. Thanks Bob

I am going to purchase a set of lower control arm stiffening plates for this 68 barracuda, just wondering if anyone has a set they want to get rid of and are not going to use before I order a new set. Bob

I am looking for a stock choke assembly for my factory 1968 340 intake manifold with the 4 bbl Carter AVS Thanks Bob

I am looking for a nice rally Dash face plate with AIR and glove box plate. I don't want to give up my first born so Let me know what you have. Thanks Bob

I am looking for a nice set of 1968 Barracuda tail light assemblies for my car. Don't need to be perfect it's going to be a driver but I don't want housings that are pitted or lenses that are cracked, I already have that. If you have a set and I don't have to give up my first born let me know...

I need a bolt for the 90 degree oil filter adapter, I have my adapter for my 340 but my bolt grew some legs and now I can't find it. Let me know along with shipping to Michigan 48346. Thanks Bob

So I picked up a 1976 small block 727 that was in a Little Red Express Truck. It had a column shift and this 68 Barracuda has a floor shift. So I am looking for a long tail shaft for this 727 with the two humps behind the trans mount so I can mount the bracket. Thanks Bob

I am looking for a trans cross member and trans mount for this 1968 Barracuda with a 727 trans. Please let me know what you have and a price along with shipping to 48346 Michigan. Thanks Bob