Search results for query: *

That's a question you don't asked everyday! However, I'll show you my tires and this is after I was done trying to shove the largest tire inside the fender well.

Here I have a three piece passenger side taken from a 1964, 65 Plymouth barracuda was used for Garage art. Great piece of nostalgia! The fender does have a dent in the front but can be easily fixed. No known holes in the lower sections of the fender which is rare just some surface rust should be...

Thank you everyone!

Hi everyone! Forgive me it’s been awhile since I posted here but I do browse time to time. I have a question. Is it possible to use the 360 balancer seal (given in my gasket kit) in a 64 273 timing cover? I’m transitioning all the front components over (water pump, alternator and power steering...

I'm still on it! After making the frame rails and part of the trunk floor section and fabricating the entire tie section that supports the frame rails to the trunk and the lower valance. Cutting myself, burning myself, getting metal in my eyes, ears and mouth i finally got it back together.

Thanks you all for your nice comments. Here is a pic of the removed rusted piece.

Yep I'm still working on her! Finally finished the Frame rail for the Passenger side just need to prep the car to weld it in. I'm getting better at making them for sure. I finished both quarter patch panels from Laysons and wheel house fabrication as well. Here is a pic.

I believe it's 36 inch cheap Harbor Freight chinesium. I used 16 gauge for this which is really to heavy for this style bender but I used Map gas to help along.

I had to build mine from scratch for my 64. Using a cheap bender and some basic hand tools.

Thank you! I purchased this car from a gentleman who used it as his dailey driver to and from the steel mills in Gary Indiana. It was a Midwest car its whole life and showed it with decades of Cancer top to bottom, but it is a factory 455/4 speed M-20 trans. It still has its original block...

This is my Oldsmobile I customized years ago. I drive this to local shows and cruise nights. I love this machine!

I had purchased the old Mopar prostock plastic scoop and used it as a template to build a steel one but chose to hide the bolts. This is near complete just some minor welding, some filler and finished. I made it in two pieces. It is a little larger than the stor bought and I made it a inch...

You have to look closely at the spline.i have found a photo for comparison. And the ring gear shows 2800270 3:23 for 742

Do you think it all still needs to be shimmed any where?

741 case with a 742 pinion...I hope I can salvage something with this case..it all turned before I took it apart..and it was no bind or slop.. Sean

Here is another photo.

Here is another photo.

Here is the inside of the cones..I will bet the previous owner got them hot.

Ok I will take some photos tomorrow and post..thanks for replying! Sean

I Purchased an A bodied 8 3/4 741 differential that looks like it was separated from the car and sat in a backyard for years. Taking it apart carefully trying to preserve all bolts and nuts I noticed the pinion matched the pinion of 742 case and then looked at the numbers on the ring gear and...

Looking for drivers side fender, is it possible to send a photo?

I think it's great you guys decided to do this! You are doing a great job! Can't wait to see more.

Check with laysons restore..I think they supply the corners for the gasket..They are starting to produce more for our cars.

How far in the city are you located, I am interested.. Sean near valpo indiana

Thanks guys.. Instinct was saying find a pro, sometimes I need help to push over the edge...tomorrow I'm going to look for a pro who can weld it..thanks!

Hey guys, and girls.. I scored a 727 trans connected to a 318 for small money, I always wanted to dIY a trans upgrade, so I installed the reprogramming kit in the VB and disassembled the case, as I was power washing I found a 3 to 4 inch crack next to the line up stud on passenger side of bell...

Trans is sold

Thanks for the response..I found a good small 727 but still have the 4speed.

For trade or sale..I have a 96 360 magnum engine disassembled needs cleaning and reassembly.. Good block, crank, pistons, has roller cam..all good shape should not need machining.. Trade for 64 barracuda drivers fender, trunk lid, 8 3/4 dif..located in Hebron Indiana.. Local only

For trade or sale best offer 4 speed overdrive trans, has hurst shifter, shift rods, I have pedals but no bell housing.. Trans has two shifter locations..looking for good 727 trans with stall or 8 3/4 dif or 64 barracuda parts. Hebron Indiana