Search results for query: 318 cams

One of the things I question myself is .... when I did the cam swap only, it was back in the day. Cams are "smarter" so to speak? Maybe now, the cam would produce more of a result ?? But heads have come along way also.

IMO Post 15, is on the money. IMO the 340 cam in the hi-compression 340 only worked as well as it did because of the package it was in, which included; a high compression ratio, log manifolds, a lightweight chassis, and limited rpm in a street application. IMO that 114LSA which may have...

i i have promaxx heads on my 318/390 stroker.....ported them a little...widened pushrod pinch....blended chamber/seat area...unshrouded inlet valve ... has a lunati hyd roller......232/[email protected] lift....port matched airgap...750 mech secondary....11-1 comp....excellent street combo....pulls...

If leaving the 302 heads stock, I wouldn't bother, time and money for no real gain. You a least want to gain head flow if doing a swap, A magnum head or milled 360 swap keep/gain cr while giving more flow, if willing do some porting can add 273/318 heads back in the mix but you can also port the...

Depends who you ask :) it looks about right to me, think about milling a bit of the heads and or deck to bump cr closer to 9:1 ?

A stock '69 340 pre- low compression, smaller valves debacle, had according to NHRA 300+ hp. That car new would run low 14s' all day easily without headers. Remember, Ronnie Sox drove one with fender well exit headers, Holley carb, Edelbrock intake, 4 speed, 3:91 SG to 13.3 106 mph with street...

if you're talking straight up easy and cheap-- 5.2 or 5.9 magnum, snap on a 4bbl intake send the cam to oregon and have it reground, thin headgaskets to bring the compression up and roll. if you're even thinking of going roller cam on an LA, start with a roller block. or, again a magnum...

Man, I've tossed Bunches of cams... who would have seen this coming?

Heads are basically the number 1 component for NA hp especially streetable hp, look to the LS 5.3l same basic displacement, smaller bore not overly high stock cr. In dyno trim (headers, tune, no accessories) stock cam makes 350 hp and with a 218 @ fifty cam well into the 400 hp range and most...

A Manifold thread turns to Cams. I love it. Still have not installed my Isky but I know it will be monster. Was told this should not be annoying with 904 and 3:23s. Will benefit with more stall. The car is just so pleasant to drive as Chrysler intended I am waiting to swap when I can massage...

May as well, just go for a generic brown box Hydraulic flat tappet cam.

Do not burden yourself with all those whose first response is to build a 360. Nothing wrong with 318 engines. Yes it is easier to get 400HP out of a 360, but sometimes you go with what you have or have available. What heads are you thinking about, and valve sizes? Aluminium are lighter and not...

I know the Voodoo line is more aggressive, but I was unaware they actually used Mopar lobes.

Probably so. 73 340's ran pretty good but they were pretty anemic compared to the 68 and newer ones. 73 was the last year for the 340 and everything got a 318 or 360 from there. The 360's were built like the 340's of that era. Heads, cams, manifolds, etc were interchangeable. The 360 would...

@Dan the man Here are some theoretical cams, to show you what happens to LSA/etcetera, whilst adjusting the overlap period. this is just an exercise. all are in at split overlap. I set the Ica to 62* for a compression period of 118, which is typical street I set the intake/exhaust split to 4*...

Well, they were when I bought the 60404 that’s in the 340 in my Duster and the 60403 that’s in the 318 for my Dart. The Lunati’s have faster ramps than the purple cams did, higher lift on similar durations. That would be really tough on a narrower lobe.

i think you've got a lot of the bits and bobs there to make something pretty rock and roll, but it really comes down to budget and pain in the *** factor. as somebody that's always built my own junk on a beer budget, and currently going thru a "dedicated cheapskate" 318 build i can certainly...

IMO, again, don’t worry about the cam, use the 340 block, stroke it with an all forged rotating assembly. Can you port your own heads?

KB 167's are a popular option. Near 0 deck height. They are around 10:1 with a .039 gasket.

Stick with cams like 340 cam or 268 Comp Cams. Note. The performer has smaller ports than the 1973 340 TQ intake has. I know you say you have the Performer but you will be running 318 small ports on a larger 340-360 port head. It will ne fine low end mid range but will reduce power on upper...

keep in mind, the cam in the 360 was going to have a stock torque converter and highway gears... started as 2.45's and now 3.23's. Better converter and gears, the engine would come to life with a better cam. It's why I say, if you do not plan to go to the drag way or race the car ever, just...

Well and compression.

To the OP… what cams did summit suggest for it? Also, what head gaskets were used in the changeover? If it’s not something close to the factory steel shim head gaskets with the usual stock 68cc or more actual open chamber 318 head volume, a cam larger than a stock 318 hydraulic flat tappet is...

244@ 50 cam might not be enough to get a 318 in the 10’s, it’s possible, but I would want something bigger. your gonna need convertor anyhow, might as well put a big boy stick in it, if your serious. to me, minimum.. Mechanical Flat Tappet Camshaft; 1964 - 2003 Chrysler 273, 340, 360 3400 to...

But under 3000 rpm we spend most time at part throttle which means the engine only making what it needs to do normal driving which is not much and it's only a fraction of the hp the engine capable of even at low rpms. And at full throttle how much time do we spend under 3000 rpms anyways...

Yeah, i had to think back many years. Same intake and carburetor as the 360, stock compression ratio 318 bottom end, mildly ported 360 heads, 273 adjustable rocker arms and a Comp Cams 270S solid flat tappet camshaft. Sounded like a big block when we opened the headers.

RR of the Day: unholy cool 1986 Chrysler 5th Avenue - Autoblog thanks, sold it 11 years ago when I got my toxic orange charger RT....wish I could have kept all my cars....after this submission, I had pulled the 360 and built up the original 318 short block with magnum heads and a reground...

Is anyone here old enough to remember what D/Modified Production cars ran in the mid 1960's? Did they run flat tappet or roller cams in M/P back then? Found this pic in an old book and though it would be cool to build a tribute engine. Just wondering what the performance potential might be. I...

Hmm...I got a cam reground by Bullet and it has .520" lift. I put it in the 360 in my Duster with Hughes retrofit roller lifters. I wonder if we ended up with the same cam.

I know off the top of my head that factory 340 heads are pretty much done between .480 and .50 No idea what 273 is. The zebra dart's 318 was a blast off the line. Had a pretty "mild" cam in it. Good for coming off slow and moderate turns. Only real issue was the car was going W2W road...