Search results for query: *

I ran into the same questions and delima, twice with the Dart.. once with Hoopty. It's just really hard to make any decision, without the trans bolted up to where you can raise and lower it. With Hoop, I didn't want to "C" notch one of the bed crossmembers and put it as high as it would go...

welcome back...you were on here for a long time...2010 to 2022. Your old profile still contains your posts, 100 percent rating and 2800 messages! 8 Garages thanks for the pictures

Don't cheap out on oil, buy Brad Penn (or whatever their new name is) or even Comp Cam break in oil (mineral), I was led to believe it has a higher amount of ZDDP than say VR1 and the like. Ignore any posts that say you should breakin with Synthetic ;) I used 10w30 Comp break in oil and my cam...

I may have a good one. I can see later today.

I am interested in the stock one

I have not yet driven the car with a rack which k member I've done 2 now stock or tubular?

Hello my name is Brian, I bought my 1970 340 swinger in 1978 right out of high school. I was previously known on this form as k.o. swinger but haven't posted in a couple of years. I lost my password and no matter how many times I sent in I never received an email back? Don't know why.so I...

1950 plymouth suburban with title needs restored have all parts except rear tail gate has a flat head sux in car would make nice one 3200 obo

Are you going to make a cross member to tie your frame rails into ? This will be interesting to see how you do this, if you plan on leaving the rest of the sheet metal alone. I sectioned my entire pan after removing the spare tire well & the cut the ends of the rails away from the body, slid it...

Wow....it's the Russkie Tona! :eek:

https://www.kijiji.ca/v-engines-and-engine-parts/st-catharines/mopar-340-main-caps/1703520462

Along with Joe Dirt and Bad Chad

Welcome from West Virginia.......................

1) Hurst 500 0025 Quarter Stick 5' shift cable NEW - $65.00 2) Perma-Cool 1013 Trans cooler - 18,000-20,000GVW rating NEW - $50.00 3) Custom Hurst Quarter Stick mounting kit. Bolt shifter to plate, spot-weld nuts to underside/blindside, disassemble & weld bracket to desired location on...

If you are really concerned about it, call Bob at Glen Ray, he restores them. He can answer your question. He is located in Wausau, Wisconsin. Maybe your radiator is do for a restoration anyway.

Quick question about the k-menber you had with the rack in it. Did you ever drive the car like that & do you have any more pictures of it ? I would love to duplicate that myself.

I don't get Christmas gifts. I finance others Christmas gifts.

Welcome to FABO!

The way I see it, is if the lower ball joint arms cam be duplicated in height from the ground then that's a good starting point. If the rack is in the same place as original steering linkage then it can't over center. Sean, I like your ideas. You've built your car completely, chassis and...

So, My plan is to do the rear half of the cage once the floor section is installed as I going to narrow the rear frame rails and install 38" tubs up to the narrowed frame rail. I have to get the support to the rear of the car prior to that. That way the rear of the car is structural prior to...

I see now. Thanks

s/b distributor $60 ,gas line and fuel pressure gage $45, 83/4 and dana shocks EC $90 pr,car plates $30 pair nice ,yokes 83/4 with straps coarse spline $75fine spline no strapes$45 nw 6" chrome dual pully march $50 all items plus shipping or pick up mansfield ohio

Welcome aboard!

I've seen people shorten racks, might be better off starting with a wider rack and cut it to size if you can't find the ideal width. Couldn't you just fabricate new tire rod attachment arms to keep proper geometry ?

Welcome from Texas, post pictures of your project please.

Not sure if bench bleed applies to this type of Master Cylinder.

I take melatonin when I have trouble sleeping, that stuff works. No gummies for me, too much added sugar. Me and stimulants is a bad combo! I would suck as a drug addict!

To put 2024 "behind me" :)

Bummer Fred, you would have loved it down here. Not a straight road in the County and not 100 flat acres anywhere! Plus wearing a hoodie for Winter clothes! And a darn good plan shot in the butt! See ya next summer!

Can any one tell me if a door from a 71 dart is basically the same door as on a 72?