Search results for query: *

TQ sold, manifold pending.

No, not at this time. Looking to sell not trade.

Bump Thermoquad $275 Shipped. Intake manifold $60 pick up only. Trying to scrape some pennies together to replace my AC in my daily. Thanks

Probably last call before I toss it. Bump

Bump

Bump, open to offers.

Just changed my seats in my 73 Valiant from a bench to a set of pro car buckets. My current belts are the retractable lap belt with attachable shoulder belt. Obviously the buckle part is too long since it was for a bench. looking for a set of front belts for buckets that I can replace them with...

Bump

Decided to sell my 6318 (1973 340 manual transmission) thermoquad I purchased in 2020. I originally paid $400 for it from a credited rebuilder who has an ebay store. This is not some Rockauto Reman, this one was rebuilt correctly. I originally wanted to run this on my 318 but after only 2 weeks...

In the end you people are listening to a washed up youtuber, that at one point used a mallet to hit in a camshaft in a fresh hemi block that the owner if the GTX had just spent a grip of money on at the machine shop. I thought his stuff was informative in the beginning but left after his bs and...

Bump

Bump $350 shipped. I'm taking a loss but need it gone.

Its the angle of the photos, I'm able to center them all on the head now after I ground the pedestals down. Just some fine tuning left to do with some shims.

Couldn't of said it better. No point in cutting corners with all the time and money into this engine.

Well I think I about solved the problem, and I learned something. Shaved some of the number 1 pedestal, Yes I know now that I didn't need to take it down that low. but it now clears the rocker. Also, like Kendog mentioned above I had to take the center pedestal in a little as well, it now...

You are not wrong! turns out that pedestal was interfering as well. I had to grind that one back a little bit and now its able to be centered. Now all I need to do is get the correct spacers. Here is that rocker you were questioning now.

Makes sense. I will check everything once it's bolted down after I grind at the pedestal. The center of the rolers on that cylinder look like they are to the right. I will see if this bumps them to the left a little. Otherwise spacers will be next.

I will have to check tomorrow. But seems like this head was off quite a bit then the other.

Ok my Dad said to check the thickness of the inner pedestals and I think they are the culprit. The good side shows' them to be more centered. The side in question the numbers are not so symmetrical. Good side: Side in question: The picture with the measurement of 0.319 is the rocker...

They measure out the same but I think I may have to just grind one back a little

To be clear the shafts were on a set of X heads but now they are on a set 974 360 heads. What puzzles me is that the same shaft that will rub on the number 1 exhaust will not do this if I swap it to the other head. I have checked all the thicknesses on the spacers and rockers and they are all...

I am mocking up the rocker arms on my 340. I am using a set of Crane 1.5 rocker arms that came with the engine I purchased. I am running a Mechanical solid cam. My issue is during installation I am noticing that the outer arm on for the number 1 Exhaust is rubbing the shaft mounting tower. This...

Here is the seller's shop who rebuilt this carb. stevestill0 on eBay

Decided to sell my 6318 (1973 340 manual transmission) thermoquad I purchased in 2020. I originally paid $400 for it from a credited rebuilder who has an ebay store and dose this on the side with great feedback from other buyers. I originally wanted to run this on my 318 but after only 2 weeks...

Pending to GTX JOHN.

Listing a set of X heads I am not going to use. They cam off of a 340 I bought a while back and I am using a set of later 360 2.02 heads. IMM checked them for cracks and they are good heads. Guides are good as it looks like the previous owner recently replaced them. Selling these bare, $400...

Here are notes I have from the seller when I bought it. Looks like the setup it has currently is listed on the bottom left. The extra parts I have are listed on the lower right.

I am not worried about the thermoquad having mismatched parts the seller has an excellent reputation on rebuilding thermal quads and this can be shown by the seller's feedback. Yes I have the thermoquad adjusting tool and I did mess around with the secondaries when I had it on my 318. But I was...

Ok so a little more info. I drive my valiant daily with a 318, it has a huges whiplash and am currently using an Airgap and Edelbrock 600 CFM. I don't need to source an airgap as I have one but would prefer to keep it for a performance 360 I plan to build in the future for my Dart sport. The...

I do have a factory Intake, lucky it does not have EGR, I just hate how heavy they are. Did not think they were any good other then just being a factory intake.