Search results for query: *

It is exactly 4" from the edge of the stainless to the center of the front mounting hole. I measured the trim piece on the other side, the one that did not fall off, and from the edge of the stainless to the tip of the > shaped trim piece is 4 3/4". This measurement is 3/4" longer because I...

Ive theorized someone could 3d print empty bulkhead connectors.

i didn't know mopar made chevy's, not seen one of them that don't leak :rofl:

208/212 @050 260 advertised. .440 lift Good low rpm street cam. Mild, good torque will work well with factory converter if automatic and low (numerical) gears.

If you have an OEM sample PM me. I can definitely make that. Could even make them in Aluminum

Gotta love hot steel being worked into something. I spent 41 years at a forge shop turning steel bars into all sorts of shapes for various customers in the USA. Mostly Cat, Deere, Dana.

The little plugs that go into the hole below the wing vents. I forget his name now, but a guy in Florida made 3 of them for me, 3-D printer. The cap plugs that are sold to replace them are terrible. Bet that a lot of people could use them.

As mentioned 68 and older does not have molded in timing mark.

PM me if you have a sample.

That is more doable. If you have a sample bezel, doesn't need to be radio delete or in one piece,PM me.

Ok, I’ll add I have a late model water pump too. Maybe I’ll re ask the question “ what timing cover do I use for a 7.3 inch balancer”….

'69 Barracuda small block single exhaust > Chop Chop. Did not know they ran the single pipe down the driver's side. Head Pipes, maybe you can find a single exhaust Y-pipe take off that you can cut for your head pipes??? I use single exhaust Y-head pipe on my engine run stand. 76 small...

Sorry to hear this news Fred!!

A friend was asking about them too. Problem is the cost to produce would be prohibitive.

I can do the CAD BUT the cost to produce would be prohibitive

It's now not listed as an active fire. So it's out. I'm pretty sure this is like 1/2 mile south of the actual park we use for Spring/Fall Fling. There's a "Natural wildlife area" there. AKA a bunch of wild dry brush. It was headed across Burbank ave toward dam and there's nothing there to burn.

Pushbutton delete bezel on 64 Plymouths.

Too large for my capabilities. But thanks

I run the same cam in my Barracuda 5.9 based engine . Mine is 222/229 though.and I have IMM prepared EQs plus 1.7 Harland Sharp rockers . Gobs of torque ! Although I am getting valve float over 5k. I didnt realize that my heads had the beehive springs vs the doubles . I will be changing that...

That cat is ready to kick some azzzzz, correction, all the azzzzz!

Calipers in aluminum. sbp I'll take 2 sets.

My 99.9% stock 340's would run 14 flat go 165 and get about 20 mpg on snow tires with no posi. no o.d. Stock exhaust system. I have plenty of witnesses. There may be some better stuff out there but it always worked for me. Now add 1.6 rockers, 11.0 to 1, o.d. 4.10's headers etc. what would you...

Not mopar, but: IH KB series headlight trim rings. Very thin pot metal on trucks with sketchy brakes!

Yeah but the Hughes magnum intake is pushing $1k after taxes and shipping, yikes

I'm in the same boat with a B body. Not sure if they will fit an A but found these. 1974 DODGE CHARGER MagnaFlow 19343 MagnaFlow Performance Manifold Pipes | Summit Racing

Yes, exactly why my posts previous to the one you cherry picked stated that I recommend everyone get out of the way of a wind driven fire and draw a bigger box. Don't make me think of you a fool. It is an elfin Forest and has timber (Mt. Laguna, Palomar Mt., Pine Vally, Cuymaca .......). For...

My 87 Ram had straight pies on when I acquired it. I put a 5.2 magnum in it. I uses to love pulling up next to guys on those pipes Harleys and power brake the Dodge. I'd blast by those yahoo and almost k rock them off their bikes. Got a lot of looks from those guys!

That sucks. sorry for both of you.

My first thought was to head to exhaust shop for the flanges and some pipe. I need something to get the car running. Currently no exhaust at all. Then I could probably either use the 2.5 duals, I have (made for the 70 Dart floor, axle exit) or buy a summit kit. So I will take the manifolds...

fillister head screws for the rallye bezel (tall #8 I believe...chrome and black) apparently air cleaner pie tins are NLA