Search results for query: *

Hi there, do you remember the length of the shocks for your hood? Did you just guess for the placement of the pivots? Thanks

LoL,

I hear ya, Well thanks for the reply. Hopefully you got all your remodelling done. Cheers

Hey JDMopar, I know I'm seeing this post from a few tears ago. I'm doing a 5.7 with a 545rfe swap in my Dart. I was wondering if you can send some advice my way.... I was wondering if you have anymore pictures of your build. How did you do your trans mount, what shifter did you use for your...

Oops, yes

I have for sale , a Kelsey Hayes brake kit. Parts came off a 72 Scamp. Work fine when pulled off. Everything there minus the upper control arms. Calipers, rotors, pads, spindles, bearings, lower ball joints. Asking $600 US plus shipping.

Hi there, vin is OR192056. Date code is 116 140 69 it's hard to read on the block but pretty sure that what it is

Hi everyone, I'm looking to sell some parts. I have a 2008 Gen 3 Hemi with only 25000 KM on it, no accessories has front drive on it and comes with a intake. $2200.00 US plus shipping. Torquer 2 small block intake. $75.00 Also might be selling my 340 with only about 2300 miles on it. Rebuilt a...

Thank you!!

These are .830 in diameter and are in good shape. $ 75.00 Plus shipping Also have 8 3/4 axle adjusters for sale $25.00 plus shipping

Yes, my mistake.

Selling pair of clean torsion bars out of my 63 Dart 6cyl. bars. Has 622, 623 on the ends. Clean bars, they still have the drip marks from factory. Asking $100.00 plus shipping. Also have a set of Mopar 8 3/4 axle adjusters. Asking $50.00 plus shipping

How much to ship to 32081?

Would you ship to Canada? Your I Florida?

Hi, How much for the dash frame, also how the condition of the drivers fresh air vent? Thanks

What year cobra? 99-04 or are they for the 07 - 2014. Thanks

Any chance you have pictures, and price?

Have a cigarette lighter and wiper switch. Great condition for the age. Lighter element has the bezel as well. $30.00 each plus shipping. Dart GT inner door emblems. $50.00 for the pair plus shipping

Vintage Accel dual points distributor. 30301 is the number on it. Small chip at the bottom of the cap, was in a small block 340. $30 plus shipping. Also have front bumper brackets from a 64 Dart, possibly fit 65, and 66 but not sure. Little surface rust nothing bad though. $75.00 plus shipping.

Selling a pair of good used lower ball joints from a 63 Dart . Has LBJ nut as well as the spindle bolts and nuts. Looking for $50.00 for the pair. Plus Shipping.

Running Cordobra 11.75" with single piston and mustang set up in rear. I would like to go a bit bigger in front with a better calliper. I have 17" front and 18" rear. Any suggestions? I don't like WilWood and Baer are high on price.

Hey there, do you guys build brackets for brake conversions?

Probabaly no lower than 2", if I just turn the bars then the K gets lower to the ground. What spindle did you go with? MF? Fat

Do you think 1.03 bars with adjustable shocks would be fine? So would you do drop with new t bars? Or could I get away with just bigger t bars? I appreciate the help/advise.

You’re running an 18” up front correct? And the caliper hits. I have 17” Foose Knuckle, when your bracket is done would you be selling any additional ones? I already have a set of hubs machined. Just looking for a bracket, hopefully to run the mustang GT 13.2”

Perfect thanks, do you know anyone selling a pair used? I checked my t-bars last night...I believe they are 6cyl ones the # on them 622/623. Would you say you need heavier bars? If so what are you running now? I do like mine to be low, but last summer I’m pretty sure I’ve bottomed out a few times.

Hi there, I saw a post on drop spindles....I saw a pic of your 64 Dart. Did you have any issues with the k member hitting or bad ride quality? I’m not sure which way to go...drop spindle, or heavier t bars and just turn them a bit. Any help or advise I’d appreciate. Thanks, TJ

Your car looks great by the way!! Love to see the bracket when your done.

Hi there, may I ask.... what year mustang rotor are you using, and also what caliper bracket are you using. Thanks

Hi Andy, I just saw your post on your front brakes with 911 calipers. I was wondering if you would be up to sharing some info? If so could you please contact me. Thanks, TJ