Search results for query: *

Looking to sell my Holly six pack setup complete with nitrous plates, bottle heater, purge solenoid, hose, pressure switches, chrome air cleaner and Edelbrock LD6B intake manifold. Carbs are manual secondary and fuel inlets are on driver side. Located in Plainfield , Illinois 60585. Shipping...

Looking to make some room in the shop, all must go at the same time, local pick up only. Located in Plainfield, Illinois just west of Chicago. $100.00 for the lot.

Looking for a crack free pair of 1972 Duster tail lights.

Just had time to post the dyno report for my new 408. It will be going in a back-half 72 Duster that should come in at about 2600 lbs. I hope to see the nines for the 1/4. Brian at IMM did the head and intake work, Indy 360-1's flowed 328 at .700, Indy intake, Ferrea 2.08 x 1.60 valves, T & D...

Looking to see if anybody has used the 1 7/8" W-2 RACE TTI headers with the Kevko m-202 oil pan on a 408. Sam at TTI had no experience with Kevko pans. http://www.kevkoracing.com/images/m201m202_full.gif http://www.ttiexhaust.com/Header-TTI340W2-178/op1.JPG

Anybody ever install roll cage or back half from them. I am looking to install their stuff in my Duster. Thanks in advance Frank

I am having lifter bore bushings installed in my 360. My machine shop needs to have the center to center data for the cnc. Thanks in advance for any help.

Looking to put a motor plate in my Duster with a small block.

SOLD For sale: $125.00 for both or $75.00 each plus Shipping from Plainfield Illinois. Pair of Sterling hanging unit heaters. 100,000 BTU's input. 80% efficient. Used, very clean and both work. We upgraded to 98% furnaces for our shop. On a pallet ready to ship. Cash, check or money...

150 Video: 1975 Duster at Route 66 Raceway Category: Race Videos Uploader: LETSRACE

So far this season I blew two head gaskets in the same spot.The top of #2 cylinder, it blows into the motor and blows oil out every seal and hole in the motor. I have a 340 with the high comp. pistons, .030 over bore, Standard stroke, 360 j heads, six pack carbs and manifold, shooting 150 h.p...

Anyone else have any problems or suggestions? We have had a problem at work and at home. We use and update virus protection by Mcafee. All firewalls on and active. It took out all large programs like word and quickbooks. The wife is about ready to toss me to the dog house. I need to log in from...

Just wondering if any other pics are on this site?

Im ready for the start of race season 3 weeks before it starts. Looking for low 12s or very high 11s.

I have a 340 with a 4 speed and only have 5 bolts that line up in the flywheel to the crankshaft, the 6 th hole will not line up but the new crankshaft has a threaded hole for the 6 th bolt. Do I need 6 or will 5 work.

The other day at the track I had gear lube leaking from the vent on the tail of my 4 speed trans. I checked the level with the 1/2" pipe plug and it was just below it. The lube is 80/90 and I never had a problem at the track before with gear lube leaking could the problem be in the tail section?

I have manual drum front and rear brakes in my 75 Duster, the cap for the master cylinder leaks after I run the car hard. I replaced the cap and gasket, that didnt work so I got a rebuilt master cylinder and put that on that didnt work. I noted a small space (groove) for a vent in the cap so the...

What is the rule for the wire size in cars? I know for non auto wire 12 gauge is 20 amps and 10 gauge is for 30 amps is the same true in your auto? I noted in my duster I have some 10 gauge wire for the starter solenoid which has 49 amp draw but only has a 10 gauge wire.

I have a 75 duster that I needs a clutch switch for the MSD launch limiter. Anybody have any ideas?

Check this link out a HEMI doing a 1/4 mile wheelstander. http://www.dailymotion.com/video/x2k2yp_hemi-under-glass_auto

Anybody have a six pack with nitrous. I heard that dual plane intakes are not good for nitrous execpt the 3x2 set up.

Has anyone added front sway bar to a 6 banger duster? I am not able to tell by the service manual picture if the brcket on the lower control arm is all one assembly or if it can be added.