Search results for query: *

So, I work in Saudi Arabia. A friend told me about a car show, was not sure what I would see. The show was decent sized, lots of different makes, from Rolls Royces to VWs. Good stuff. I spoke with the owner of a 69 Camaro and he told me they actually do Cars and Coffee here. Will hit that up...

Anybody here own one? Due to a rough motorcycle accident years ago my back is getting more and more sensitive to a mattress I am on the hunt for a new one. It is a pretty good chunk of change, figured I would get some opinions if possible. Looking at the I10, king size, standard base, not...

So, I have gas powered yard tools. However, I work overseas and am back for 30 days every 90 days. The individual that does the yard while I am gone has a bad shoulder, so starting the equipment is difficult for her. So, I need to buy battery powered tools. What brands are you using, if anyone...

anyone here using the Holley HP system with a Gen III? Having some wiring issues.

I bought a Holley EFI kit from Johnny two years ago when I was working overseas. I finally got around to installing it, or trying to anyways, now. Even though he works for a different company, and it is two years later, he is helping me out - no small task with me dealing with electrical stuff...

I have a A41 joined to a 6.1, when I went to put the starter(Chrysler mini starter) on it the selinoid housing hits the block. Pics aren’t the greatest but it shows the issue as best as I could get it. Any advice or experience with this is greatly appreciated. Thanks Jason

Please show how and where you ran your fuel lines and mounted your filters. Hoping to do it once. Thanks! Jason

i purchased an adapter for my 6.1 and went to install it. I am not wanting to hurt anything. The instructions cover 5.7 and 6.4, and the threaded tube the filter attaches to has hex head built into it, the 6.1 does not. I got this kit from Bouchillon and they are closed until Monday or I would...

Emailed Dr Diff with a few questions, but have had no response. Ordering a Dana 60, is there any reason to go with other than 1/2 x 2 studs on a street car? there were quite a few options. Also, for a street car, Trac Lok is the best choice, correct? Last, any input on gear ratio suggestions I...

those that have done the swap, what ratio are you running? I have read different things as far as the rpm the g3 will be happy cruising at. I am ready to pull the trigger on a rear end, but want to buy once(hopefully). I thought I wanted a 3.55 or 3.23 to keep highway rpms down, but read it...

i am finally back from overseas and will have a garage again in a month or so. I am finally going to have the time to put the 6.1 I have in my Barracuda. I currently have an open 3.55 that has to go. I am on the fence about throwing a Dana in. At what Tq level should I ditch the thought of an 8...

ok, have done a fair amount of research, but still undecided. Those with epoxy or over coverings, let me know how you feel about your covering still. Ease of installation and durability. BTW, I finally got it. Bought a house with an 1800 square foot garage.

I am taking a job which will put me in Dallas from about June to Thanksgiving or so. Already looked for Mopar clubs, but wanted to see where you guys are meeting up and hanging out. Leaving Charleston SC, I am hoping I will meet a bunch of guys, no offense to the new car crowd, but people with...

I called Dynamic from Afghanistan last night, spoke with Frank(I think). In a country where, I hate to admit, customer service is lacking, I found DC fantastic to deal with. Asked lots of questions, and most importantly, didn't just try to sell me the most expensive crap. Recommended one a...

So, I bought a 6.1 used. The engine is in the states, so I can't really get any other numbers off the block. I took a pic when I bought it and these are the numbers. 6H362156 Are these numbers relevant? They are on the block just below the heads if I remember right. I searched all over...

Those with hemis, what rpm are you running on the freeway? I am trying to nail down my TC and rear gear. Ran an rpm calculator and with a 3.55, with 17 inch tires I will pull 2300rpm. I figure a few hundred rpms of slippage from the TC I am a bit over 2500. I think it will be a good place...

Not particularly a HD fan, but just saw a Cuda in a commercial touting under 3 models under $12000. Not too may Cudas under 12k. Jason

I need a 518 rh rebuilt, can anyone recommend a builder? Buichillon? thanks Jason

So, I scored a fast tbi, but need the pump and plumbing. Will the FAST pump kit be everything I need? Did some searches, but am still unsure. This is the kit I am looking at Amazon.com: FAST 307503 EZ EFI 550HP Fuel Pump Kit: Automotive

So, I had a 318 with a 500cfm on it, got crappy mpg(10-11)-tuned ok. Changed to a 360(mild), 650 eddy, tuned decently, 10-11 mpg. When first started, takes a bit to get it moving, is that the pump? Anyway, thinking the tranny is part of the cause of my mpg , thoughts? BTW, 36 total, about 18...

I have a 9077 TQ I want to put on my 360. Here is my problem-what do all these ports connect to? I researched and found some info, but nothing concrete. Does anyone have a pic of a TQ with all the hoses connecy to? Damn, I am used to only having about 3 lines hooked up! This thing has 7 or 8!

Just a quick note, I have a 73 Barracuda and purchased front and rear Hellwig sway bars. I put the front on a few months ago, and finally put the rear on yesterday. The rear is the adjustable one. This totally transformed my wallowy(is that a word?). The car is completely different. Before it...

Need to make space, have the following for sale Trim-rear seat trim, one side rocker panel trim,window trim,quarter panel trim,and a few other misc pieces(10 pieces in all)- all for the low price of $75- I am an e body guy, I will send you pics of all so you can verify the pieces and where...

Need to make space, have the following for sale Trim-rear seat trim, one side rocker panel trim,window trim,quarter panel trim,and a few other misc pieces- all for the low price of $75- I am an e body guy, I will send you pics of all so you can verify the pieces and where they go. 2 front...

This review is for guys(like I was) that can't decide which sway bar manufacturer to use. First off, this was done on an e body, but still will show the quality and results etc. I installed a 1 1/8 front bar on a 73 cuda and the results were fabulous. Install was straight forward and the...

I need to make room. I have 12 pieces of trim for sale, I want to send it out as a group, don't really want to separate. The trim is-rear seat chrome, window trim, one side of the rocker panel trim. Honestly, a few pieces I don't even know where they go(I am an e body guy). I have the trim that...

Had contact with someone who needed/wanted interior door trim. Misplaced the email address. Please PM me. Jason

I have an opportunity to get a A500 from a Shelby Dakota. Worth the trouble? Read up on it some, wondering if it is computer controlled. Advise?

Left anf Right side. Pretty good shape, not perfect but real good driver stuff. $40 and shipping is on you. Jason

Nice chrome valve covers for sale. $30 and shipping is on you. Send me an email address for a pic. Jason