Search results for query: *

The Kit is unused and still in the box that Scat sent it in. Comes with forged KB 4.030 dish pistons, (10.2:1 with 62cc head), Kings bearings, rings, forged I beams and cast crank. Would consider trade for a paxton novi 2000 or vortech v2 kit for a magnum engine. Price is firm at $1200 shipped...

I am selling this car on CL. Looking to get around $1200. The CL price is inflated for the lowballers:banghead: Car is located in Hercules Ca. I would be willing to ship at buyers expense. More pictures and video available for interested parties...

Check this out. Possibly an alternative to F&Bs efi 6pk setup, if this guy ever mass produces .... dual quad would be cool too: http://www.dakotart.com/forum/showthread.php?t=7717

I never really see 408s that have anywhere near 100k miles on them. Do any of you guys have "high mileage" stroker motors ... more than 40k miles?

So I just pulled the heads off of my 318 mag. Running too much boost, and blew my head gaskets. Had some bad valve seals too. I was gonna send the heads off for some porting while I had it apart. I'm considering rebuilding the bottom end also while I have everything apart ... I already have...

Mopar M1 2bbl non-egr and 50mm F&B TB. Both used for around 30k miles. TB is nice for a lightly modded magnum 5.9 or 5.2, while the M1 will not be the limiting piece in most setups. Asking $650+shipping for the combo I also have exhaust manifolds from my 98, $50...

Well here is the list of things that I need or want. I am no hurry to get these parts, so I will wait for good deals. I would prefer to pick up somewhere between San Fran and Los Angeles. Shoot me a PM with whatcha got with a price. -Front and rear bumpers and brackets -Left splash shield...

Not mine, but a pretty good deal for someone going efi. I have used accel dfi and it is the shiznit. http://www.dakota-durango.com/forum/showthread.php?t=119401

Where can I find a replacement for a reasonable price? I have the oe threaded kind. Is there a way to put a grommet in the cap so I can use a cheap push-in autozone pcv.

On my 65 dart 273 AT I have a stromberg ww3 carb. I pulled it apart for rebuild and it runs better than it did before. Unfortunately, the carb still leaks a bit of fuel and after I tore it apart again it turns out that it leaks from the throttle shaft and that the throttle body is warped. I...

I just rebuilt my stromberg WW 2bbl. But I have an extra part! Where does this go ... it isn't in any of the parts diagrams. http://picasaweb.google.com/lh/photo/ryu46KyXblRbZVIWTXRMkQ?feat=directlink

I need left and right, must be in good condition. I can pay cash or I have a set of 1998+ dakota exhaust manifolds that I can trade.

I am in need of some lower quarter patch panels for my 1965 dart gt. I found two rust free full quarters locally for $100. The seller doesn't know if they are 1965 or 1966. Is there a difference? If so, how can I distinguish them?

I decided to get a ssbc disk brake kit for my 1965 dart with 9" drums. I need some 10" drum brake spindles. What years will work. Is it only 1967-1972? Also, which lower ball joints do need? I can use the stock sized uppers, right?

I am looking to upgrade to front disk brakes on my 1965 dart. I am still debating whether to go BBP or SBP. Major factor is cost for me. Will the kesley set-up fit under factory 13" wheels? If not will any of the aftermarket sbp kits fit? If I need new wheels immediately, i might as well go bbp....

Hello Everyone, I recently picked up this car to use as a driver/beater. It has clean, driver quality interior, and runs pretty good. I am starting to really get a kick out of driving the vehicle, and I am thinking about restoring/restomodding it. The problem is that the body is not so...

I found a leak in the hard line that goes from the fuel filter to the carb. Where can I get a replacement. Probably going to replace the whole section from the fuel pump to the carb.

YouTube- 65 Dart vs Mustang.mp4

Being a young gun I cut my teeth on computer controlled fuel injection cars. I just bought a 1965 Dart GT 2732bl and the timing and fueling is all out of whack on that thing. Can you guys recommend any resources (books, videos, websites) to get me started futzing around with the carb and...

Can anyone recommend a good body guy in the San Fran area? Will need to be capable of minor rust repair.

Anyone have any pictures of cars painted this color. Especially looking to see it on early A bodies. Thanks.

Not mine but looks like it might have some good parts! http://sfbay.craigslist.org/pen/cto/1804353429.html

Hello All, I have been shopping for my first A-body for a while with no luck. I am looking to spend $4-6k. I need something that moves under its own power and isn't completely rusted out. Basically looking for something that is drivable while I fix it up. I really want a 67 with v8, but would...