Search results for query: *

I don't think I understand what I know - or think I know. I picked up a "741" case with a 3.55 open diff in it at a local swap meet. It had a bad yoke on it. I had 2 other 8 3/4's with 741 cases, so I was just going to swap one over (there were all small joint yokes). I pulled a replacement...

I have an 84 Chrysler New Yorker FWD with the 2.2 turbo. The engine doesn't run. Anyone interested?

I would like to delay the normal upshift slightly. I have a 904 behind a 340 in my 67 Dart. I installed the Trans-go shift kit when I built the tranny. The shifts are good and firm under normal accelaration, but quick. I have adjusted the throttle linkage till I have full linkage travel at...

Howdy folks, Finally got the exhaust on my 67 Dart and was able to drive it on the road. Do not at all like the power steering -- way too much assit. Is there an easy way lower the pressure a little? Thanks, Brian

Howdy folks, Uploaded a few pictures of the progress on the dart in my Photo Garage. Hope to send up some descriptions of what has happened so far -- sorta inspired by Capt Kirk. :-) Brian

We put a nice new radiator in the Dart the first of the week. Got all the hoses and such hooked up and got to the fill er up point. At our shop, we vacuum fill our cooling systems -- gets all the air out and you don't have to worry about air pockets. I ran the 67 cooling system through my...

Howdy, I am in Gainesville, GA -- loacted about 50 miles NE of Atlanta. Working with a 67 Dart GT -- going back mostly stock with exception of a 340 in olace of the 273. Brian Gordon

Howdy folks, I am considering getting some blasting equipment for cleaning. I want to be able to do smaller itiems, but also hoods & door etc. Any suggestions on the equipment and the best media to use? Thanks Brian

I have aqquired a set of 72 340 exhaust manifolds, any reason they would not fit a 67 Dart? Thanks guys.

I am using the old style screw in PCV valve in 273 valve covers. The problem is finding the rubber groumet for the valve to sit in. Anyone have a source for these? Thanks. Brian

Howdy folks, Has anyone tried to use the late model Magnum exhaust manifolds on a 67 Dart w/340. I am not wanting to use headers if I can help it. I have not found a set of 340 manifolds that I can aford and thought I might try to get a set of the Magnums if they would fit ok. Thanks Brian

Howdy folks, Am going through the steering column on my 67 GT. To get the shift tube out, I had to pull the neutral safety post that moves the switch out of the tube. Simple enough, just pull it out of its retainer in the tube. Getting it back in is the problem. The repair manual says to...

I am considering buying a 340 block, rods & pistons and heads minus the crank. I have a 67 273 with a nice forged crank in it. I realize that this is not as strong as a 340 crank, but does anyone see any problems with this set up if the engine is just as a weekend driver on the street...

I have been given a 1978 Volare with a slant 6 under the hood. It is a four door and has been sitting for a number of years. This will be given free of charge to anyone who will come and get it. It is all there and I am going to sent it to the crusher by the end of the week if no one wants...

Hi folks, I am going through the Evaporator / heater box on my 67 Dart. Most of the various air or temp doors have installtion stuck to one or both sides. As you may know, it has just turned to powder and must be replaced. Without this on the doors they have a tingy metal noise when they...

Trying to get some info on my 67 Dart GT. I need to find out where to get the information to deciper the tag that sits in the left wheel well. I have been able to find out what each section is, ie: axle, engine etc. But I don't know how to deciper the codes. Axle is: "2" Trim is: "P6R"...

Howdy folks, My 67 Dart GT arrived Friday, at least the first shipment. With the exception of the rear end, K member, front fenders and rear quarter windows the car came completely disassembled. The engine and trans & hopefully a few missing peices are due to arrive next week. I have...

Hello all, My name is Brian Gordon and I hail from Gainesville GA. I have been an owner / restorer of several 69 340 GTS and Swingers. I am contemplating starting a new project -- a '67 Dart GT. It has been a number of years since my last one (sold it in '95) and with the rise of the...