Search results for query: *

Sold it $3500. Four people made $3500 offers so I figured that must be a sign. There’s still good deals out there and I thought you all would appreciate knowing what it sold for as we can always see what people are asking but not what they actually sold it for. Thanks for looking.

Sale is pending! Thanks

1971 Dodge Dart Swinger Located in Hamilton Michigan Asking $4200 Arizona car, absolutely no rust. Body has been sanded and partially in epoxy primer. Subframe connectors and mini tubbed. 8 3/4 rear end narrowed 55.25” wide axle flange to flange Stock 57 1/8” Large bolt pattern factory...

I have a 67, 68 and 69. The 67 and 69 are parts cars all of which are notch backs. I will check and see if I have what you need. I am interested in trades, do you have any 68 parts left over? deck lid trim, useable tail lights, side marker lights? This will be for a ratty type driver so...

I am looking for just one 15x7 slotted cop car cruiser wheel. Located in west Michigan, looking to pay up to $50 or so. thanks Joe

Looking for the complete rear bumper assembly. Bumper, mounting brackets and lights.

I agree X2, that's what I have on my 67 with 4.25" backspace and everything fits. I'd be more concerned with the rear. I'm running 255/60's and they rub the fender lip when I do doughnuts! lol I could roll the lip for more clearance.

$100 shipped to Michigan? I need clips too if you have them as I'm switching my 67 over to later model trim! Thanks Joe

Your Jeep, known lovingly as a "niner" has quite a few one off parts. Only ten thousand of these were made in three different colors and only in 98. It was the fastest production sport utility until Porsche came out with their thingy. The steering wheel and shifters are leather wrapped. The...

Thanks for the response, my thoughts were to use the obd2 stuff I have and make a reliable fun driver. Then, upgrade for more power. I am familiar with the stock stuff but not sure about modifications especially when you get past headers and intake mods. I have read some on the Dakota R/T...

I love this build! I have never seen motor mounts like those before, very interesting how they did that. I have to say that the aluminum valve covers do not match the patina of the car like the original dirty ones did! lol Keep up the good work and keep us posted!

My question is what would be the best donor vehicle/year for Multi Port Fuel Injection? I would like the benefits of OBD2 but Ive heard there may be some reasons to avoid the first years of OBD2? I already have a 93 ram van with 5.2 OBD1 and a late 95 ram van with 5.2 that is OBD2. I have a...

that looks great, nice work on the cooling system. This is motivating. Have you figured out the belt setup with no power steering? I will be running a/c with no power steering on mine so Im a little curious how it will be done. Again nice job, that will be a nice running and driving car!

I had maddogs on my dart and at that time they where a B motor manual trans only header. They are also 2" primary tubes and a multi piece race header, the collectors kind of aimed on an angle under the crossmember. I ran them on the street and didnt have issues but you may if your car is...

Did you mean to say 1995 318 magnum? If it is an 85 it may not be any better than the 318 that currently resides in the car and it wont be a magnum motor. Make sure it is a magnum motor or I would pass on the $200 purchase.

There is a lot more potential here! It seemed like it would barely spin the rear tires! The launch sounded like you were on a Sunday drive. Something is not right. That engine should shred those tires and launching it on street tires should be near impossible without massive tire spin. Your...

I see its been a while..... do you still have the four blue interior door panels, I need them for my project. thanks Joe

You gotta love the Box! I think we will always have one in our life.