Search results for query: *

where is the best place to buy brake hoses, I understand that the copper gasket may be aproblem in some hoses, thanks Jim.

can I use one of the new small wireless speakers for my ipod, in My 63 Dart, instead of the more expensive speakers(aka) underseat, thanks Jim.

My neightbor has a big bolt rear with the regular yoke, what else would I need to swap from the ball & trunion, thanks Jim.

Just installed a dual mc on my 63 Dart, looking underneath the rubber brake hoses are starting to split. I'm going to replace all the lines , and hoses . Can anyone recommend where to get them, thanks Jim

I bought a dual master cylinder from rock auto raybestos mc 36221. What do I do with the plunge rod, do I take the insert on the new mc out, and replace with the old , or do I have to get a new rod, I'm stuck help, thanks Jim.

I need to replace the whiskers, do you have to take the glass out? Can anyone give me tip on how to do , its a convertible, thanks Jim

how about instrument cluster, Jim.

What wires and plugs are you guys using, also rotor cap, thanks Jim.

how much for the dash pieces, including the guage console, also do you have a steering wheel, and what kind of shape is it in, Jim.

I did a compression test, all cylinders 115 Lbs, also put a vacuum guage on,steady as a rock. My brother said maybe a bad dist. cap I did get bit by one of the wires I tried to take off while running, so may get new wires, any other suggestions, Jim.

to do the poor man's test , do you have to have the plugs out, I had the valves adjusted after it started missing, didn't do any good. The car runs good while driving, its just at idle, thanks for all the input, Jim

I thought it was my ignition was causing a miss, well after chasing it down for a week, my neightbor came over , another slant 6 guy. we pulled the plug wires off 1 at a time, and # 1 didn't change. Put on a new plug wire, still the same. Neightbor says maybe head or piston skirt, Will do a...

I'm sorry my petronix is the original not the 11, does that make a difference Jim.

I installed a petronix 11 in my 63 Dart. was running fine for a while,but started to miss . I have all new ign parts except the coil. I bypassed the ballast resister, hooking the 2 wires together, miss is gone.. Do I need the ballast resister, thanks Jim.

Has anyone made there own tool for removing the front bezel of the key ignition, they are $20. on ebay, thanks Jim.

I need a new exhaust on my slant 6, but want to go a bit bigger then stock, maybe 2" . Is there a stock header pipe I can use, a friend says a 74 truck wiil fit. Any suggestions?, Thanks JIm.

how much for the keys,Jim

Sometimes my temp guage is working then goes to zero, after a little while it starts working again, any thoughts, thanks Jim.

I want to install new speakers, if I could find small speakers that I could velcro underneath the fresh air ducts would be great. I was also considering the undercover speakers. I don't want to cut into my stock panels, any suggestions, thanks in advance, Jim.

I'm changing my MC to a dual. I bought a new line block from Year One, now I have it in hand I see it has 5 outlets. 2 run through the block, 2 are next to each other, and 1 is one the side by itself. There were no instructions, can some one draw a pic, or tell me what lines go where. I fell...

someone a while back stated that you can hook up a Ipod to an car amp, and play it direct, just hook up speakers. Has anyone done this tell me what I need , I have an amp, and ipod , my 63 Dart needs more then am . I looked into secret audio, but too much money from my SS check, thanks Jim.

Moe, don't know about 64, Jim.

I see that Laysons has the windshield weatherstrip for my car,its a convertible, but I don't see the locking strip, or clips. My locking strip isn't chrome its black rubber. does anyone know where to get the lockstrip, and clips , also can another model or year fit my Dart, thanks in advance Jim.

I'm going to install a dual master cyl. on my Dart. I want to use conifer lines, what size are the brake lines, and would 6' be enough, thanks in advance Jim.

Looking for a set of trans push buttons, must be in good cond, Jim.

Was a clock an option in the 63 Dart, I have a 270 vert, thanks Jim.

Need a working temp guage for my 63 Dart, must be in good cond, Jim.

I need to replace the universal joint, I uderstand that you can convert to open type. Can someone give me info on this, thanks in advance, Jimk.

2 questions, what is the knob on the spedometer guage for, Second I'm going to paint the console, what have you guys done. My friend says paint it the same as the interior, another says dull aluminum, and yet another says, chrome paint. Suggestions, idea's, thanks in advance, Jim.

Ill take,will send private message