Search results for query: *

I installed XHD springs from Mancini in my 70 Dart and am disappointed that the car sits too high for my liking now. It is 1/2" higher on the right too. Will they relax a bit as I drive it? I don't want to buy new springs if I don't need to. So far only about 3 miles have been put on them...

Looking for the correct style "solid" press-on pulley for a Federal pump. The pulleys with "spokes" are offset too far forward to line up with the crank pulley. FSM shows this type of pulley for v8 application.

Doing a restomod on a 70 dart, s6 to 360. Considering a 3/8 fuel line with no vapor return line. Also wondering if the stock tank, with its factory 4 hose vapor vent system, would work okay with an unvented factory style painted gas cap. I think it should be okay. Any advice out there?

My 360 was recently rebuilt by a local experienced and respected builder. It has not been installed into the '70 Dart yet. The intake manifold bolts I provided him are 1 1/8" long, not knowing if that is what I needed or not. The intake is a Performer RPM with Edelbrock heads and gaskets. I...

I will be painting my 70 Dart. I removed the body rub strip that starts at the front and goes down the middle to the rear and it will not be replaced. I have welded closed all the holes down the body to the rear, but there is one in the headlight extension. This extension is made of some type...

I will need the column shift linkage for my 70 Dart project as follows: column linkage to the cross bar, the cross bar, and linkage to the trans. I have the cross bar and linkage from the s6/904, but don't know if it will fit the 727. Will sb/904 linkage work? I will also need the...

I am doing the s6 to 360 swap in a 70 Dart, column shift. I have the original s6/904 column shift linkage, chassis to trans cross linkage bar, and a throttle cable/trans bell crank bracket and the threaded kickdown link from a v8 with the upper bell crank set. As for the kickdown linkage, I...

In converting from points ignition to the electronic with added MSD, should I change my old wire loom to a factory reproduction one for electronic ignition? This would require the right resistor and control box, unless the MSD replaces all that (I have never had one before). Also, some...

I have started the process! All the great info and posts by other members will certainly inspire me to see it to the end. This is the car in my avatar pic. I got it in so. calif. about two years before I moved here to north Idaho when I retired. It was a 2 owner car with 73,000 miles and...

I pulled the cam out of a 360 I bought from a friend. He thought it was one of the purple shaft grinds but couldn't remember which one. It has some yellow paint on it at the front end and then some purple paint behind that but only for the first four lobes. The number 987550 is stamped on the...

I am building a 70 Dart with a 360 and auto trans. I have an opportunity to buy a used 727 from a 1981 ramcharger or b200 van (seller isn't sure) that was mated to a 318 4 barrel engine. I will be rebuilding the transmission. Will it line up with the trans mounts? Thanks for the help.

SOLD Rolling chassis was originally a 273 auto column shift with bucket seats and was painted Turbine Bronze. Usual rust issues behind rear window and in trunk, overall rust not real bad. Underneath is in good shape, floor pans solid. No engine or trans. Bumpers decent, trim needs some work...

Has anyone installed the new gauge panel fo A-body from Mancini Racing? They look like Auto Meter gauges. I am interested in one but haven't seen it installed and don't know how difficult it would be to put in or how much (if any) cutting would have to be done. Also, if the speedo is...

Will I need to replace the slant 6 shackles on my 70 dart when I put in the XHD leaf springs and the 8 3/4 axle?

Can the seal or o-ring around the shaft on the top front driver's side of the trans be replaced easily? I think that is where my worst leak is coming from. I also will replace the neutral start switch o-ring if possible as well. Advice? Thanks in advance- JIM

I bought the IV4 solid state instrument panel voltage regulator and installed it today in my 70 Dart non-rallye dash. It was a bit of a challenge to do it without taking out the dash, but I was able to do so by removing the plastic steering column trim and cramming my hand up inside the dash...

My 70 Dart had a rim blow wheel, it is non functional. The former owner installed a horn button on the dash to pass safety check. I want to replace the wheel with a standard horn button type, maybe an aftermarket one. Can it be done without too much drama?

Newbie here, thanks for all the advice in advance. 1970 Swinger headlight switch works great except when the rheostat is turned CCW so I can see the panel in the dark. That is when the fuel gauge and temp gauge go to their extreme max positions. When I rotate the switch CW to turn the panel...