Search results for query: *

THAT WAS A LOT OF TIN WORK, EVERY TWO INCHES USED A POPRIVET !

I STILL QUESTIONED AS TO WHY YOU MOVED THE MOTOR FORWARD, YOU SAID TO GET MORE LEG ROOM, I AM 5 FT 10 AND TOP AT 190. WHEN I PUT THE CAR TOGETHER I SET THE SEATS UP OFF THE FLOOR AND LEANED THEM BACK DOING THIS GETS YOUR LEGS OFF TH FLOOR AND LEANING BACK SHORTENS THE DISTANCE TO THE PETALS ...

Need a update on your project, hope you have not given up!

Bought them with the hope that they would work on my B body but will not so my loss is your gain. New way $110.00 with freight asking $85.00 no shipping cost to you. Frame rails I used on my B body had a wide front spring box was hoping for a little more rood on springs by using the off set...

Yep that is what happened to my brothers Vega, He was going to put it back on the street and put his wide Mickeys back on it, while playing around in front of his shop one of the tires went flat, it hooked hard right and drove into a bank and rolled over bending the car up good, spools are bad...

It's a 472 crate Hemi I bought many years ago, was run a dyno at 528 hp I just want to drive it and not race it

My Last I have to do 74 years old. 1965 AFX Coronet 426 Hemi with 4 speed. SLOW but I will get it done!

Remember you moved the motor Forward 12 to 15 inches. When I had the Hemi in it you would have to remove the blower and put the single 4 barrel in take on it to pull the motor. That was a lot of weight moved forward, I built the car for the street with no thought of racing it.

THIS IS MY SMALL TIRE CAR !

I have see what a spool will do to a car on the street. A friend had a Vega with one in the rear, coming from a car show he was following me, and I needed to stop for gas, giving a turn signal and turning end to the station he followed with a little speed and his car started to bounce snd jump...

Rear has 4 spider gear mopar trac lock with 4:10 richmond gears. I used 4:10 with the 32-inch-tall tires on the street, gives you about 60 mph at 3000 rpm. Has Dutchman axles with 35 splines. Any Questions send me pm with phone# and I will call and talk. John

FYI Check the front wheel bearings I did not pack them when they were installed for him to pick up !

At one time that was what I was thinking for it. I have built 3 sets of headers for customers over the years, it would be easy on this car. Headers by Ed carries all the parts you will need to build a set of zoomies with baffle's it would be sweet . John

LOOKING real good .

The brake petal and master cylinder in the box on the floor is the correct one to use . The petal has the correct swing ratio to use with the master cylinder you have . The master cylinder matches the brake assembly that is on the car at this time according to my talks with Wildwood brakes ...

KILUFF SHIFTER BETTER THAN HURST AND CHEAPER ! John

Hurst push down shifter . Short throw , had to push the shifter down to get reverse gear . Used with the bracket that moves the shifter up and back toward the driver . First pic without sheet metal around trans and shifter , second shifter is in first gear , third shifter is in 2 nd gear ...

Bought this 21 years go and just had it framed " SUNDAY FUNNYS " is signed by Mr Norm and Arnie Beswick .

Just to let everyone following this build know that Dave sold the car to a man from NY state . So I have NO way of updating anything but Dave said that Randy said that he had a Hemi to go in it . Thanks for everyone following the build . John P.S. still have my 65 AFX car and will continue to...

Will be a street car , so no worry about tech check .

He got a set of 300# springs with the car when I sold it to him .

OK just a little update , A few pic's of the new motor 440 , aluminum heads roller cam gear drive .

MRE ac207 motor plate bracket from Mancini racing . Used to locate small alt. on motor plates . Bought it to use but do not have room due to passenger side water pump housing and fuel pump . Cost $67.95 never used , want $50.00 plus $5.00 for shipping my loss your gain.

I was going to use it on a manual box , I do not know the size of a power steering box . count splines on a power box and measure shaft for size . Thanks John

I have 2 pn 7238 shifter handles that came off of super shifters at one time or the other . $30.00 plus shipping

Bought these for a project and went a different way . 3/4 X 3/4 shaft drill or weld it on 3/4 X 3/4 with 36 spline for mopar sheering box Both for $40.00 plus shipping .

2 3/8 left hand thread and 2 right hand thread heim joints . Can be used for engine limiter with engine motor plate or as a motor trap strap . $25.00for all 4 free shipping

YEP use what ever on hand to make things work . A couple of my cars I built 1972 Colt and 66 cuda funnycar .