Search results for query: *

Where can you find pistons for Kelsey Hayes calipers? 71 Demon

Thanks for all the replies. Lots of different ways to go about restoring them. Not sure where to find an ultrasonic cleaner near me. Think I’ll try cleaning and soaking in Evaporust. If that doesn’t work I may try the galvanized paint and news paper trick. Thanks Warren

I’m restoring the front suspension for a 71 Demon. I would like to get the front disc brake splash shields replated. What would be the correct plating ? Any suggestions on who could do such plating ? Thanks Warren

Thanks for the replies.

Thanks for all the replies.

I was looking at a 71 parts car I have. It had one of each bumpers on it. The narrow one had a Chrysler part number on it (2948716) which is what a 71 parts book calls for. Thanks for everyone’s replies.

Which bump stop is correct for a 71 Demon ? Thanks Warren

Was the sway bar on a 71 Demon bare metal or black in color? Thanks Warren

Rebuilding the front suspension on my 71 Demon. The strut rod bushings that came with my PST kit are 1 piece. The ones I took off were 2 piece. Could you take a look at this picture and tell me if I have the bushing and washers orientated correctly? Thanks Warren

Thanks for the info.

Is your commercial guy pretty reasonable? Thanks Warren

What would of originally been on lower control arm pivot shafts, nuts, and washers?

I’ve got some front suspension hardware that I would like to treat with black phosphate. Has anyone done this at home? Where did you get the solution? Thanks Warren

Does anyone offer spray paint to replicate the cosmoline color of LCA’s? Thanks Warren

Let me know what you come up with. Thanks Warren

Wanted vinyl top trim pieces and drip rail trim for vinyl top 71 Demon. Thanks Warren

What would be the correct third member for an original 71 Dodge Demon 340? Thanks Warren

Has anyone used a reproduction rally dash bezel in their 71 Demon or Duster? If so how did it fit and did you have to make any modifications to it? I have an uncut, unbroken factory one. I am trying to decide weather to have it restored or buy a repo. Quite a bit more to restore but it’s an...

Does anyone reproduce the chrome release buttons for 71 Demon bucket seats? Thanks Warren

Classic Industries shows three patterns for trunk mats, gray herringbone, gray houndstooth, and gray plaid. Which one of these patterns if any would be correct for a 71 Demon? Thanks Warren

Is E70 14 the size tire that would of originally came on a 340 Demon? Thanks Warren

I need to order a new tank for my Demon. I was just wondering if there is a particular brand or supplier that has better tanks than any other? Or are they all made in the same place just branded different? Thanks Warren

Thanks for the replies. I should of known with 3" difference that one was 108wb the other 111wb.

I am needing a driveshaft for my 71 Demon 340 / A833 / 8 3/4. When I look them up in my parts book I come up with 2 different lengths one is 48.96" 2 3/4" shaft the other is 51.96" 3" shaft. I haven't been able to find much info on manual trans length. Anybody out there mind pulling a...

I am looking for a couple of pictures of an original 71 Demon bucket seat ( the type I have pictured) around the push button area and seat back. I am trying to determine if I have the correct seat frames. Thanks Warren

Would a set of steel wheels off of a Formula S Barracuda be the same as what would be on a 340 Demon? Same back spacing? Thanks Warren

The parts manual shows a 14x5.5" steel wheel and a 14x5.5" Norris Thermadore steel wheel. Which one of these would be correct for a 71 Demon 340? does anyone make a reproduction with the small bolt pattern? Thanks Warren

Try tonysparts.com

I am getting ready to reassemble my 71 seat tracks, and I was wondering what would be a good grease to use on them, something that will hold up to the interior temps on a hot day and not run all over my carpet. All suggestions are appreciated. Thanks Warren

Laysons shows them. Part# EQ-ACS