Search results for query: *

Mate, interested in lens only. Will you ship to Oz?-at my cost (as long as its not nose bleed expensive) Cheers, Monaro

Thanks for all your great leads I'm not going to chance spending any more money on the beast before Xmas in case the missis find out. Cheers, Monaro Have a great one over the Christmas break.

For 69 Cuda: my driver side brake light lens has a small section broken off (at the base) can you buy a lens? if so from whom or is the lens part of the tail light assemble? I am just a brake bleed off from getting the car registered and I'm worried that they might knock it back when I go for...

New levers fit spot on car should now be on road within week.

G'day fellows, just to give you a update, I think that I have got it worked out. First I laid the arm on bench ('tuning fork' end up) and measured the gap between the cut outs and it worked out at 168m (just under7"?) I then got in contact with Elko spares in Melbourne and send them pictures of...

I will take picture and post (if I can work it out). Cheers , Monaro

Thanks for help and pictures Cheers, Paul

Got another problem, when I pulled drum brakes apart I took photos on phone, then some low life stole it. I can put brakes back together all right but I got confused on which way the cable for the auto adjuster goes. I remember than on the front (10") and rear (11") left hand side-driver side...

I just set up the brakes with the bar in place I would need to file out 25.3 mm (about 1" of metal) before I could get the shoes to meet on the pin, something is really wrong here, has anyone got an old lever that they can give me the measurements for? Monaro

Thanks mate, that is exactly the problem I'm having. I have thought of that but I don't want to attack it until I'm sure that it is in fact the correct part. Because there are 2 description for the same part there must be some difference between them. Also did you take out the most metal from...

No I have done that completely slacken off. Monaro

I have finally got my car (69 Cuda) sorted except for rear 11" brakes. I need them to be fully overhauled including drums ( I adapter Ford 11" drums to fit -cost of drums and freight from US would make you faint ) The problem is that the parking brake levers were missing when I got the car, I...

I have the 'bell' drums (small bolt pattern) that are u/s. Do the 'normal' 10" drums fit? and where can I get them -again small bolt pattern. Cheers, Monaro.

That's 10" drums, have to start proof reading.

Another thing to take into account, I'm having trouble locating 10" for my 69 Cuda. The better brands have dropped them (one bloke quoted $400 for each drum-Bendix). I can get 'no name' ones over here for about $280 a pair, which would be about the same cost as to get them from the states to...

Sorry that i have taken so long to respond, the tip on R/T Spec. was the right one, found the clip-part # 1000354, Thanks for all the advise. Cheers, Monaro

Can someone direct me to where I will be able to purchase the metal clips that hold the rod onto the knob/ball at the back of the door handle on a 69 barracuda. Probably not describing it well but I hope you get the idea.

Not sure about that mate, no screws when I pulled them off and I can't get them on anyway, however you have given me an idea, will let you know how it works out. Cheers, Monaro.

I am trying to install the cable clips on my cuda heater box, and having no luck except entertaining the idea of burning the car. They are new clips and as much as I try to hold the cable and the doors in the right position with one hand and at the same time trying to put the clip on with my arm...

Thanks fellows, the problem ended up being that the yoke was flogged out, the bolts must have worked loose in the past and then been re-tightned. Ordered a new yoke, will let you know how it workes out. Cheers, Monaro.

G'day boys, the auto electrican arrived (to finish a job) as i was just about to crawl back under the car, It looks like I have been putting it on right its just bloody tight, but tomorrow my mate and I am heading off on a bike ride (no women allowed) out west for 3 days (last week of my...

These are new uni. joints. Caps are the same size, I will attempted to clean the seats on the yoke. Are the straps normall strong enought to draw the caps completly into the seat of the yoke?

No, I'm talking about both rollers on the universal joint installed on the shaft not fitting completly into the seat of the diff yoke, so that I can't installe both the straps.

Is there a special way to fit the universal joint into the yoke on the diff. section. I have been under the car for hours trying to get the shoulders to bed into the yoke, they go about half way in, I can get 1 strap on but the other side sticks out too much to get the other one on. Also is...

Mate, I just brought one to install on my Cuda 727. Instructions say 'Chrysler 727,904, 518 Hi-Tech Kickdown Installation Instructions'- so it must fit. Also if you trawl through the auto. and final drive forum someone has posted pictures of the kit installed. Cheers, Monaro.transm

Thanks fellows, be lost without you blokes, trouble with readig from offical workshop manuel is that they seem to write it like you have done it before (well that how I see it). Tony cactus= stuffed, u/s, buggered etc. well I'm just about to crawl under car before it get to hot (second month of...

Sorry, 69 Cuda 727 t'mission going to a 8 3/4 sure grip diff. Cheers, Monaro

Front universal joint is cactus, seemed simple to change from the book until I crawled under car and attempted to remove (by the book), is it better to remove rear uni joint to gain better access to front? or is there another way? Cheers, Monaro.

Tony, plenty of parts over here. Car not running yet, but not to far off. Its a 'on the tree' shift which I think woul be akward to change. So its just a valve body change? Cheers, Monaro

I think that my 727 had been changed to a manuel change (ref. to previous thread), is it a big job to convert it back to auto while g'box is in car. I saw a manuel conversion kit from Summit and it looked like there was not much it the kit so I'm hoping that it may be a simple job as I have the...