Search results for query: *

  1. 80fbody

    Pushrod Length Question

    Mine came out to 8.125" for lowdeck with Edelbrock RPM heads, solid lifters & HS rockers. That measurement is to bottom of cup.
  2. 80fbody

    Pushrod Length Question

    Perfect. Thanks.
  3. 80fbody

    Pushrod Length Question

    I'm measuring for pushrods on my 470 build with solid lifter cam. I've taken the measurement with checking pushrod at approx zero lash with two threads showing on the Harland Sharp rockers. Should I reduce the pushrod size to account for lash. I think the card is around .018" hot. How does that...
  4. 80fbody

    BB Oil Pump Difference?

    Mine are 1 3/4”. Thanks for the help. Anyone have a write up on prepping/blueprinting these HV pumps prior to use?
  5. 80fbody

    BB Oil Pump Difference?

    Unfortunately I don’t have a known stock pump to compare. I was hoping someone had the rotor heights. Neither of these are marked so may be new stock pumps
  6. 80fbody

    BB Oil Pump Difference?

    Is there a quick way to confirm whether a big block pump is standard or high volume? Got a couple new ones hanging around but not sure if they are the M63HV I need for my 470 build.
  7. 80fbody

    400/470 - Cam Bearing Question

    Excellent. That's definitely reassuring. I did some reading and there's some that have recommended installing a restrictor to limit oil to heads a bit to keep it at the mains. Not planning to do anything like that but seems a bit of a reduction to the heads may be ok.
  8. 80fbody

    400/470 - Cam Bearing Question

    Awesome. Thank you guys. Surprised they don't oversize the holes to give us a little play.
  9. 80fbody

    400/470 - Cam Bearing Question

    Edelbrock rpm heads. The bearing has a couple marks from test fitting but don’t believe there are any gouges.
  10. 80fbody

    400/470 - Cam Bearing Question

    Should I be concerned with the 4th cam bearing that feeds the heads? Neither side is great. Probably 2/3 open at most. It’s gonna be a 400/470 strip mule approx .625 lift.
  11. 80fbody

    Clutch fan vs derale single 2400cfm fan

    I'd try the Derale if you have the room and a good alternator that can handle the load. Make sure to use a good relay. Can always fall back to the clutch fan if you have room. Derale & Spal are great fans typically.
  12. 80fbody

    Head gasket sizing

    Definitely don't want to try and get a gasket the same as the bore. If it overhangs the bore or chamber at all you'll end up with problems. A little bigger is typically better.
  13. 80fbody

    [FOR SALE] cams convertas and few more parts

    Yes unfortunately mine is a 6 bolt crank.
  14. 80fbody

    [FOR SALE] cams convertas and few more parts

    Interested in Billet Flywheel to break in my motor when it's done. Mailbox is full. My email !(no emails in public forums, in the rules. (Thank you) Thanks, Jay (Or phone numbers) Text Ok
  15. 80fbody

    Dana 60 vs 8 3/4 -Steve Magnante Hemi Dart

    Steve's a really cool guy and very, very knowledgeable with many makes. Not just mopars. Obviously this is like Facebook and we just rip apart every word or action someone does. Certainly not a stupid guy.
  16. 80fbody

    Electric water pump diy

    They made adapters for this on the big blocks. Not sure on the small blocks.
  17. 80fbody

    470 TrickFlow 240 Solid Flat Tappet Cam Dyno Results

    Thanks for the post RAMM. Trying to get my 470 built myself if I can ever get the block finished at the machine shop. They're killing me.
  18. 80fbody

    [FOR SALE] Stroker pistons

    I think 440 Source uses Ross to make their pistons.
  19. 80fbody

    [SOLD] 383/400 Weiand intake

    Does it have a part number on it?
  20. 80fbody

    What rear axle to purchase and narrow

    Quick Performance 9" or start with a housing/axle package from Speedway Motors. They have tons of widths for for around $799
  21. 80fbody

    LT1 T56 Transmission to LA 360 swap

    To the OP, I'd forget that t56 and save for the new TKX five speed. Gonna be alot less of a headache. I have a new magnum and wish this had been out at the time I grabbed mine. I'd have been all over it.
  22. 80fbody

    CRE Stud Gridle Installation Tip

    Very nice. Good tip. Appreciate it as I'll be installing my first "girdle" this winter.
  23. 80fbody

    MSD GRID

    Curious, did MSD's recommendations help?
  24. 80fbody

    Degreeing Cam by Measuring Overlap @ Lifters

    Buy a degree wheel and follow the instructions. It’s another tool in your toolbox. Buy a decent one and you’ll have it for many years.
  25. 80fbody

    [FOR SALE] 11.75 Pin Type Calliper Brackets

    Hmm, unfortunately I’m not sure which spindles are on mine. I’ll have to see if I can figure it out.
  26. 80fbody

    [FOR SALE] 11.75 Pin Type Calliper Brackets

    I take it this allows for larger front rotors on an A body? What spindles does it work with? I have disk brakes on the dart now but don't believe they're that big. Would be nice.
  27. 80fbody

    $476 to assemble an 8 3/4 diff

    This is exactly why no one wants to work on old stuff for money. Unless you figure you're time at $25/hr they think they're getting screwed but the same rear end work on a newer Ram would be couple grand with basically same **** (Bearings, Ring & Pinion, Axles, Seals, Etc)
  28. 80fbody

    Lowest cost 400 stroker

    Just get a 440 source kit and be done. You can offset grind a stock 440 crank but as you said, no one wants to screw around with that stuff anymore. Better to get a kit, have the shop mic it all up and test fit in block so you don't have any issues. Then assemble yourself.
  29. 80fbody

    Tool C-3968

    Would a simple $60 valve height micrometer work here? Good to have in toolbox.
  30. 80fbody

    Line Lock Light

    I used a small 1/8" or so red led on last street car. Simply drilled thru dash. This came on only while the unit was actually activated and I had a light up switch that was used for power to the relay. Basically, flip switch on (turned green) then I knew that there was power to the unit...
Back
Top