Search results for query: *

I'm installing a new electronic ignition engine wiring harness in my 69 roadruuner. I would also like to install a new solid state voltage regulator made be Regitar Model:C524 I have a new Mopar ignition module and have everything wired up (i think) but need some input on how and if I can...

I just bought a 26" Champion Aluminum Radiator model# CC374, for my 1989 360 engine in a 1969 B-Body. Does anyone know if there's a mopar shroud that will fit or can be modified to fit the 4 bolt pattern on this model. Please advise, thanks.

Can someone tell me the length of the metal bushing/spacer for the power steering pump mounting bracket? It's a 1989 360 engine, I can't find the original but will have to make one. Take a look and let me know, thanks.

I just upgraded my 318 engine to an MRL 408 Stroker, in my 1969 Satellite. I'm having a problem installing the power steering pump as the water pump on the other engine had an ear on it to attach the power steering pump bracket. The new water pump dumps to the other side and that's the only...

I have a 26" radiator part number 2949 059, does anyone know where I can find a shroud for this, or have one for sale?

I found one thanks.

Looking for a two grove crankshaft pulley for a LA360 small block. This is the one that bolts on the damper. Let me know if you have one for sale or trade, thanks.

I'm looking for a small block 727 transmission fluid fill tube and an inspection plate. Let me know if you have one for sale. Thanks

Can anyone tell me if there's a place where I can find a header stud kit for Small Block Edlebrock Heads with 5/16ths exhaust port threads? ARP only has 3/8th's studs and I can't seem to find these anywhere. Let me know thanks!!

Drive Shaft-- used for one season, last year replaced u-joints, balanced and powder coated at shop. Length is 55.5 inches from middle of u-joints front to back, length of shaft is approximately 52 inches. This also comes with differential yoke and 904 transmission slip yoke, see photos. This was...

Just completed front disk brake upgrade along with new master cylinder and power booster, rear brakes are drum. I have a clean system what brake fluid would be best, let me know your thoughts. Thanks

Looking for a recommendation for a set of studs to mount the headers on my edelbrock small block heads, also what's the best header gasket. Want to make sure I get the best so I don't have problems later. Also, are the end holes water jacket like the iron heads? Any mounting info or experience...

sold

I'm looking for a bushing for my power brake linkage, the small one on the right. Anyone know where I might find this? I was told the part number is 2534346, but have had no luck finding one. Thanks

Patriots win, total points 58.

Can anyone recommend a radiator shop in the Chicago area that does good work. I need my Mopar Radiator re-cored, and was looking for some references, thanks.

My address William Darcy 2250 Linneman street Glenview Illinois 60026

I'm installing new engine with a 904, I'll take them and send you a pic of the installation.

This is a great deal, last chance going on ebay!

All three pieces shipped 100.00!!!!!

Christmas Special all three pieces 100.00 shipped! FOR SALE- 394 oil pan from a 1969 small block with new gasket 50.00 plus shipping, also have 90 degree oil filter adapter 65.00 shipped, both working in excellent condition. I have additional pictures if needed.

I'm installing a 408 stroker in my car and I currently have a 5/16 fuel line that is like new (installed last year). Can I leave it in and run 3/8 line from fuel pump to the carb? Or do I need to replace the whole fuel line to a 3/8, which requires new sending unit as well.? What kind of issues...

Can anyone tell me where I can find the correct fan shroud for a 26" 1969 318, radiator Part # 2949059 ? Thanks

I bought the same one yesterday for my new iphone, very happy with as well!

I have a complete 318 engine for sale, carb to oil pan. The engine has 360 heads,purple cam, new water pump, electronic ignition in distributor (Pertronix) Edelbrock 600 Carburetor with electric choke and Performer Intake. No brackets, belts, pulleys or linkage will be included as I'll need them...

Can you send a picture of it to [email protected] I'm interested, thanks.

do you still have these?

Edelbrock LD4B intake for sale, nice condition removed from running small block engine. No cracks, or broken holes just bolt on and go. 145.00 Shipped to Continental USA. I'll also include a new set of Fel-Pro intake gaskets and valve cover gaskets. My engines done, maybe you can use them...

I have a 1969 318 block with heads, crank, timing chain cover and oil pan for sale. Also comes with Edelbrock LD4B intake and chrome valve covers, 200.00? or best offer, located in Chicago area. Thanks

The location is 15 miles West of Chicago, I talked to the guy and he seems legit. The engine was built for racing and some local shows but is definitely not a daily driver.