Search results for query: *

  1. 1973dusterkid

    D100 Wiring diagrams/pinout

    I left a wire out from the bulkhead the brown wire you said not sure why I did mush have not worried about thinking it need to go to the starter relay. Running good now.
  2. 1973dusterkid

    D100 Wiring diagrams/pinout

    It’s a 3 pin starter relay I removed the bypass wire from it and ran it to a start 12v wire coming from the buck head connecter and it runs good now I got 10.05 bolts at the coil with engine running
  3. 1973dusterkid

    D100 Wiring diagrams/pinout

    Ok so I have it wires just how it shows in the below picture and with the ignition on the Ballast resistor gets very hot and smokes a lot engine will also not fire any ideas
  4. 1973dusterkid

    D100 Wiring diagrams/pinout

    Thank you very much this is exactly what I needed
  5. 1973dusterkid

    D100 Wiring diagrams/pinout

    It’s a 4 pins ecu and 4 pin ballast resistor So the + coil wire and the ecu ign wire need to run off the which side of the Ballast resistor the low ohm side and have nothing running off the High ohm side
  6. 1973dusterkid

    D100 Wiring diagrams/pinout

    I have another question or if someone could lead me to a answer, the ecu runs off the 5.0ohm side of the Ballast resistor does the coil and voltage regulator run or the 5.0 ohm side too?
  7. 1973dusterkid

    D100 Wiring diagrams/pinout

    Thanks great info
  8. 1973dusterkid

    D100 Wiring diagrams/pinout

    Hey guys/gals I picked up a 1974 D100 a few weeks ago, looking for some wiring info. I am replacing all the wires on the engine harness and beefing up the charge wire, along with bypassing the amp gauge. Do anyone have a pinout or diagram of the firewall bulkhead, I’m cleaning and Replacing all...
  9. 1973dusterkid

    Install a Tremec T56 Magnum in your A-body

    Can you please send me a message I’m am interested in ordering a kit from you tr6060 and a 6.4 into a 73 duster
  10. 1973dusterkid

    [SOLD] 833 swap Setup

    Any trades I would need would be anything to help with a 6.4 t56 swap or shark tooth grill or rally dash
  11. 1973dusterkid

    [SOLD] 833 swap Setup

    Sent you a message
  12. 1973dusterkid

    [SOLD] 833 swap Setup

    It always worked when I ran it
  13. 1973dusterkid

    [SOLD] 833 swap Setup

    Abody Mopar 4 speed setup Plymouth dodge 1300 or offer/trade Non overdrive 4 speed iron case aluminum bell housing. Transmission works good, I ran it behind a 360 in a 73 Duster for a few years, everything has same wear but still works good .I am now going 6 speed. Transmission is ready to...
  14. 1973dusterkid

    [SOLD] 360 Small Block Mopar

    . I added pictures with part numbers
  15. 1973dusterkid

    [SOLD] 360 Small Block Mopar

    Yes matching springs in heads for the cam
  16. 1973dusterkid

    [SOLD] 360 Small Block Mopar

    Sorry price is 2200 Modern gen 3 hemi
  17. 1973dusterkid

    [SOLD] 360 Small Block Mopar

    LOCATED IN BUFORD GA 30518 Price $2200 Looking to sell my 360 Small block dodge set interested in trades for parts for a hemi swap 1971 block bored 30 over Big valve 2.02 j heads (ready to put on) Block has been machined and cleaned ready for assembly can bearings installed...
  18. 1973dusterkid

    HDK suspension

    Would you be able to run qa1 lower control arms with this setup or is it required to use hdk lower control arms
  19. 1973dusterkid

    HDK suspension

    How are you liking it
  20. 1973dusterkid

    Coilovers on qa1 K-frame

    I have subframe connectors and toques boxes I did just see the hdk bolt on kit
  21. 1973dusterkid

    Coilovers on qa1 K-frame

    Well non of it would be cobbled up and the shock is very close to the stock ride height and travel as factory. When to comes to geometry well I am going to do my research and when I make the new mounts I can make that work. And why because why not I have nothing better to do then burn wire and...
  22. 1973dusterkid

    Coilovers on qa1 K-frame

    Ok so I got to looking and seeing what I could do as far as installing coilovers on a qa1 kframe. Going in a 73 Duster gonna have a small block, mostly street car. I found some coilovers with a stud mount in one end, and was thinking with a properly braced upper fender well would they work? I...
  23. 1973dusterkid

    Engine bay on 73 Duster

    I like that mount I really wish I could have make a plate for the whole firewall but that was a little out of my skill range
  24. 1973dusterkid

    Engine bay on 73 Duster

    Ok so I’m at a point where I am redoing my engine bay, got most of it done other then the wiper hole. I’m gonna shave and mount a wiper motor under the dash. Looking for ideas on either just making a round plate and patching the hole or taking the whole area bump where is mounts out and making...
  25. 1973dusterkid

    Building a hot 360

    Also was wondering if it would be worth the time deburring the lifter valley
  26. 1973dusterkid

    Building a hot 360

    Ok so I’m getting ready to put the motor together this week and need some info on gapping piston rings I plan on running a 150 shot down the road so what do I need to gap the rings at or does anyone have any post/articles on how to do it with power adders
Back
Top