Search results for query: *

  • Users: coyote42
  • Content: Threads
  • Order by date
  1. coyote42

    [FOR SALE] 1968 383 and 1972 727

    For sale; 68 383 + 72? 727. I went another direction after I started this and clearing up space. 383 is baked and cleaned, bored .040 and ready for final hone and ring fit, new KB pistons with rings, forged crank is untouched, stock rods, 906 heads need redo, intake, pan, water pump housing, 72...
  2. coyote42

    727 Difference inside

    Transmission gurus, I have a Big block transmission from a motor home and one from a C body. I see on the MH one there are ribs on the tail shaft for strength, C body smooth. Are there any internal component strength difference between the two? I want to build one and sell the other with a 68...
  3. coyote42

    Power brake conversion

    Hi Guys, I got done with my wife’s Duster and been driving it this summer to shake it down. Julie drove it and would like some mods to make it more comfortable for her. I did a factory disk brake conversion and all new system but it has manual master from factory. She would like power brakes...
  4. coyote42

    1967 Barracuda wire harness

    I will be getting my 67FB back from paint in the spring and am looking up new wire harnesses for the whole car. It came from life in Arizona and they are all crispy. I have been looking up harnesses from Painless, Year one, Classic Ind and American Autowire. I am looking for some feedback on...
  5. coyote42

    VFN fiberglass hood any good?

    I saw a nice looking hood for my 67 Barracuda on VFN fiberglass website. I have to replace my hood anyway and am looking for a good replacement.I am looking for any input of people who have used their hoods before I buy one. Thanks
  6. coyote42

    340 CYLINDER HEADS

    Hello my engine gurus. A couple years ago I rebuilt my 68 340 short block. When I did I put .030 flat top pistons that sit at true zero deck with 2 valve reliefs, -5cc if I remember correctly. It has been on the shelf for a bit all oiled and wrapped up. I did this thinking I was just going to...
  7. coyote42

    Instrument cluster refresh

    Hi A Bodies, working on my 70 Duster cluster. Taken it all apart to clean and refresh paint. Couple questions, does the Standard dash lighting look better with the blue diffusers out? What LED replacements are you using? Should I do a voltage regulator update on the circuit board and what is the...
  8. coyote42

    [FOR SALE] Used 292 Comp cam

    Selling a Used Comp cam 292 hydraulic cam. I purchased it used a while back from a guy who had it in a 340. I was going to put it in my 340 but Didn’t and am going a different direction. Too big for what I want. I inspected the lobes and the wear pattern looks good. Measured the lobes with a mic...
  9. coyote42

    [SOLD] Adjustable rockers and shafts

    Set of Factory adjustable rocker arms and shafts. Picked them up then decided I’m going in a different direction and not going to use them. $100 plus shipping.
  10. coyote42

    [WANTED] 70 Duster heater control

    I am looking for a NON AC heater control. Just pulled my dash and found the plastic pins for the cables are broken. This is not a restoration. Just want to make it work. Thanks, Kyle
  11. coyote42

    [WANTED] Seat latch covers

    ISO plastic seat latch covers that look like this. From a bench seat with the bucket style high backs and arm rest. Both sides needed. Any color is ok. Thanks. According to Year One they are 73-76 seats.
  12. coyote42

    70 Duster hood to grill gap

    Hi guys, got an assembly question. I’m putting together my duster front clip. It had gotten bent up, not bad, at some point in its life. I installed the hood latch and support and got the hood and fenders aligned. I put the grill in to see how it sits. The hood latch cross piece holds the grill...
  13. coyote42

    [Found!] 70 Duster front bumper filler

    ISO metal front bumper/grill filler for a 70 Duster. 70-72 work for me even though they are slightly different in opening design. Does not have to be perfect, driver quality ok. Thanks, Kyle
  14. coyote42

    1970 DUSTER DRIVESHAFT W/904 AND 8 1/4

    I went to have my Duster driveshaft shortened to fit my 904 - 8 1/4 set up.( it was changed from 7 1/4 before I bought it and the drive shaft was stuffed between the trans and pinion) They told me it is bent and needs rebuild at $450. Is there somewhere that sells replacements for less or...
  15. coyote42

    [Found!] DRIVESHAFT FOR 70 DUSTER

    ISO a driveshaft for my 1970 Duster. It has a 318, 904 trans and an 8 1/4 rear end. (had an 7 1/4 removed before I got it) The measurement from tail shaft tip to the pinion yoke is 52 1/2in. My current driveshaft was going to get cut down but turns out its bent and would need to be re tubed...
  16. coyote42

    A999 in a 70 Duster

    Alright my transmission Gurus I have a question. My 70 Duster original 318 num match motor and trans is a mess, broken bolts and such. I have a 90 318 I rebuilt with reground roller cam and the A999 that was attached to it. My question is being a lock up converter, can I just drive it with the...
  17. coyote42

    [Found!] 1970 Duster parts

    ISO 70 Duster rear license plate bracket and light, also front kick panels.
  18. coyote42

    1990 318 rocker arms

    Hi all, I am re assembling a 1990 roller cam 318 from a truck. It is for my 70 Duster. When I took it apart I found some shaft mount rockers replaced. What I have now is some rocker arms have a offset hole in the pivot point of the pushrod and some do not. All pushrods are hollow. What is the...
  19. coyote42

    Brake Pushrod for 70 Duster disk conversion

    I have a 70 Duster that had manual drum brakes and a master with a bolt to hold the top on. I have been converting to 73 up disk setup. Car came with rotors and knuckles. Been ordering everything else. The Master I ordered was for a 73 up manual disk Duster. It has a clamp style top and no...
  20. coyote42

    Quick Question, I hope

    Hi Guys, I need some help with my thoughts. A year or so ago I rebuilt a 1990 318ci. I had the roller cam reground by "Magnum Mopar", I think it went to Oregon. I measured it when it came back and compared it to the stock measurement before it left. Looks like they took around 55thousandths...
  21. coyote42

    [Found!] 70-76 Duster/Demon/Dart front seat

    Looking for a 70-76 front split high back w/armrest bench seat and tracks for our 70 duster. I believe they came more on 75-76 years. I have a split low back w/headrest type now. Does not need to be correct year/style for our car. Thanks
  22. coyote42

    [Found!] 70 Duster front marker light, bumper

    Looking for a right front marker light and front bumper for a 70 Duster.
  23. coyote42

    [Found!] 70 Duster parts

    I have a 70 Duster. I am looking for a set of headliner bows and clips, interior trim that goes over the edge of the headliner between the A and C pillars both sides, right front marker light assembly/lens and a glove box door. Thank You
  24. coyote42

    727 or lock up 904

    Hi, I am looking for advice and opinions, dangerous I know. I have a 727 and lock up 904 out of a 1991 ram150. My project is a 67 Cuda fb , 340ci around 350hp when done, I have collected sure grip center sections from 2.94, 3.23, 3.55, 3.91 gears. I plan to drive it a lot. Some long cruises to...
  25. coyote42

    318 block decking

    I want to have my '91 318 block deck trued up. Curious as to how much can be taken off before there is cyl head and intake angle concerns. Using the factory pistons and rods. Had .015 already taken off the home ported 302 heads. Its a street engine, maybe a little compression bump too.
  26. coyote42

    [SOLD] Seats

    Bucket seats with seat belts. Unsure what they came out of. $80/ make offer. Plus ride. [/attach]
  27. coyote42

    [FOR SALE] Small block comp cam and lifters

    Used comp cam and lifters. 273-360, 292h-10, .501in .501ex lift, 244/244 @.050 dur, 110 seperation, have cam card. $60 plus ride.
  28. coyote42

    Cam grinding

    Hi, can you guys suggest a cam grinding company? I have a cam too large I would like to resize. Or get one custom ground. Thanks, The car is a 74Charger 3600lb, 318, ported closed chamber cast heads, 9:1 comp, dual plane, hedders, 2.5in dual, 727 auto/rev man, 391 sure grip, 27in tire.
  29. coyote42

    No reverse and neutral

    Just rebuilt my 74 727auto. First one. Used a B+M rebuild kit, Reverse manual valve body (used), Medium stall converter, followed directions to a T. When in reverse, has slight engagement then releases (feels like a nudge then nothing). When in neutral, it moves like it is in gear. The BM...
  30. coyote42

    No oil to pass side head.

    Just put my 88 318 together. Still on stand. Was a roller block now has hydrolic flat cam. When priming the oil pump I found no oil at the pass head rockers. Lots of oil everywhere else. Removed pass side rockers. Removed pass side head. Port is clear. Ran drill for pump. No oil. Removed...
Back
Top