Search results for query: *

  • Users: "Dart67"
  • Content: Threads
  • Order by date
  1. "Dart67"

    1967 Dart 273 4 Barrel and 383 4 Barrel Production Numbers

    I am the Original Owner (Special Ordered) of a Dart 270 2 Door Hardtop 273-4 Barrel 4 Speed. Delivery date 5/3/1967. The question of Dart models equipped with the 273 4 barrel production numbers came up in another venue. So I put this together for those that might have an interest. 1967 Dart...
  2. "Dart67"

    Patriotic 1967 Dodge Darts

    This photo was taken by my friend Spencer Gore 10/9/2004 in front of my shop in Towanda Illinois. The red and blue Darts are mine. The white dart was Spencer's racecar. It now belongs to Michael Yielding here in Arkansas
  3. "Dart67"

    Check Out my MOPAR "The Dodge Boys" "White Hat Special" treasures I unpacked today.

    A very rare "The Dodge Boys" "White Hat Special" hat. A stick on "White Hat" and a rough "I'm ONE of the Good Guys" clip on badge.
  4. "Dart67"

    57 Years Ago Today

    I took delivery of "Ole Blue" at Courtesy Dodge in Bloomington, Illinois.
  5. "Dart67"

    [WANTED] A833 /904 7290 Slip Yoke

    Like the title says, I am in need of a A833 /904 7290 (Large) U Joint Slip Yoke.
  6. "Dart67"

    A-833 4 Speed Lift on and off of Tall Transmission Jack

    I thought I would share my method of lifting my A-833 4 speed off of and back onto my tall transmission jack. I use two axle straps and clips and hang them from the front or rear cross bar on my four post lift. The put one strap around the front bearing retainer and the other around the...
  7. "Dart67"

    "Home-Brewed" Pinion Yoke Wrench.

    I need to remove the pinion yoke on "Ole Blue" to Up Grade to larger U Joints. As you know, the pinion nut has a minimum torque of 240 ft lb. I had no way to hold and keep the pinion from turning. So, I hit the scrap pile again. One piece of 3/8" thick plate steel and one piece of 24" long 3/4"...
  8. "Dart67"

    New Arrival at my shop

    My friend Glenn Davis's new 1926 Dodge Brothers Doctors Coupe. As time allows I will get it running for him.
  9. "Dart67"

    MOPARTY 2022 Who is Going?

    I Registered yesterday. I will be there late Thursday afternoon through Sunday. I will be bringing "Ole Blue".
  10. "Dart67"

    Look what UPS just brought me

    A brand New Very Rare Hard to Find Resonator for "Ole Ble". After 55 years, the original is rusted full of holes. I might Add, The MOST Expensive muffler I have Ever purchased. I was going to try to make one from the drawings I posted. But then I found this one and jumped on it.
  11. "Dart67"

    Inland Shifter Adjusting Tool

    Inland Shifter Adjusting Tool Sometime back, I put the Inland Shifter back in "Ole Blue". When I did, I just guessed at the linkage adjustments. The other day, I remembered that the service manual had a drawing of an alignment tool. Here is the page from the manual and photos of my...
  12. "Dart67"

    Charger 273 Commando 273 Muffler and Resonator Measurement Drawings

    I found these drawings on the Internet Years ago. Just came across them again today and thought I would share. Herb aka"Dart67"
  13. "Dart67"

    55 Years Ago Today

    I took delivery of "Ole Blue" at Courtesy Dodge in Bloomington, Illinois I special ordered the car. Still own and drive it.
  14. "Dart67"

    Spring Time in the Ouachita's

    The Bradford Pears are now blooming at the West end of our pond. A little over two weeks late this year. The tall Pine trees and behind them are part of the Ouachita National Forrest.
  15. "Dart67"

    "Home-Brewed" 36 Inch Box,Pan,Finger Brake

    I have wanted a Box,Pan,Finger Brake since I was a young man. I will soon be 75. I was always to broke or cheap to plunk down the money to buy one. When I need to bend something I would "Improvise" or drive to a friends and use his brake. Over the years I have watched countless Youtube videos...
  16. "Dart67"

    CRE Stud Gridle Installation Tip

    I thought I would share how I install the CRE Stud Gridle on my 512/440. I use 20 5/16" x 3/4" long bolts and 20 washers to secure the girdle to the block after applying a liberal amount of Black Right Stuff gasket maker. I then torque the 20 bolts to 120 in lbs or 10 ft lbs. After that I...
  17. "Dart67"

    Front View of "Home-Brewed" 512 Coil Near Plug.

    Right now I am using cheap Ebay LS coils. Once I am sure I have ALL the bugs worked out I will Upgrade to better coils. Four coils on each side.
  18. "Dart67"

    512 Re-Install into 1967 Dart GT Convertible from the Bottom (photo's)

    Here are photos of my"Home-Brewed" Engine and Transmission Cradle. As well as the installation sequence of the engine and transmission assembly from the bottom. The body of the car is lifted using the "Home-Brewed" engine crane. Then rolling the cradle, engine and transmission under the car. The...
  19. "Dart67"

    Main Bearing replacement guideance

    I am in the process of redoing my 440 based 512 due to a loss of oil pressure. I had to have the main journals turned .010. The block is a 1966 casting. I used Clevite Main bearing set MS-869P on the Original build. This was a Full Grove main bearing set. I am unable to find this bearing set...
  20. "Dart67"

    Oil Pressure Drop Help....

    I finally was able to take my car "Home-Brewed" out for about a 4 mile drive this morning. Runs pretty well. BUT... I was logging the drive by way of the F.A.S.T. XFI and there seems to be an OIL PRESSURE problem. I am using Rotella 15W 40 oil. 8 Quart pan and external pickup standard...
  21. "Dart67"

    Engine Bay of my 1967 Dart GT "Home-Brewed"

    Engine Bay of my 1967 Dart GT "Home-Brewed" Got it pretty well finished and cleaned up today in preparation for the St. Louis MOPAR Blast show. Also just installed a set of .92 torsion bars and got the stance leveled out and a little more road clearance and less bounce than the .87 small block bars.
  22. "Dart67"

    Not a Dart Question, Weird 2020 RAM Odometer mileage Question

    Monday 4/5/2021, My wife and I drove from our home in Jessieville Arkansas to Irving Texas to purchase my New 2020 Ram 1500 Big Horn/Lone Star. I trailered the new RAM home pulling it with my 03 Ram. I did this for two reasons. Number 1, so that my wife did not have to drive in the...
  23. "Dart67"

    Battery Kill/Disconnect Switch problem/replacement

    I have been intermittent weird problems with my F.A.S.T. XFI/XIM electronic fuel injection and my new Coil Near Plug ignition system. During the process of trouble shooting the tune by logging a number of parameters, my friend Norbs David noticed that the battery voltage was low. This prompted...
  24. "Dart67"

    Coil Near Plug conversion Timing light will not work with LS coils

    As the title of the post states, my timing light will not work with LS coils. I am in the process of finishing up my Coil Near Plug conversion on my Big Block Dart GT convertible "Home-Brewed" This is an XFI 2.0 and XIM system. The car starts and runs. I am trying to check my base timing by...
  25. "Dart67"

    More Wall Art

    Got some more of my wall art and my old car show trophy plaques hung in the shop and my Man Cave.
  26. "Dart67"

    My New Wall Art

    I have had this vinyl sticky back poster for some time now. I had found a seller on ebay that makes these with the lettering that a person wants. I finally got a back board made yesterday and with my wifes help a little while a go, we got it laid down to the back board and installed in the...
  27. "Dart67"

    A Body Fuel Tank "Map"

    I made this "map" up sometime back and have been meaning to share it here. This "map" was made using an old fuel tank from a 1967 Dodge Dart. See attachment.. I cut a hole in the top and positioned the tank as if it was mounted in the car. I then added 1 Gallon of water at a time and measure...
  28. "Dart67"

    Close as you will come to getting an OEM fuel sender..

    This is about as close as you will come to getting an OEM fuel sender for your A body..... From personal experience it is close, but still needs a little calibration. Herb...
  29. "Dart67"

    273 day for me

    Today is 273 day for me... I own 2 Darts (one of which is a Charger 273 4bbl) and I turned 73......
  30. "Dart67"

    50 Caliber CVA Staghorn Muzzle Loader Bolt Project

    This is one of the projects that I have been working on during this social distance/isolation period. My neighbor gave me an old 50 Caliber CVA Staghorn Muzzle Loading rifle last winter. It uses #11 primer caps to ignite the powder charge. I don't know much about muzzle loaders. Most everyone I...
Back
Top