Search results for query: *

1967 Dodge Dart Fuel tank, its about 3 years old no rust in tank. Like new. Has small dent that was there when it arrived from shipping. No problems with it. Black marks are adhesive from anti squeak mat on it. Includes 3/8 tank pick up also about 3 years old. Has OEM lock ring. Went to a fuel...

Are you still offering the 10% discounts for FABO members? Thanks

Price reduction $780.

Both the headers and the down pipes were thermal coated by TTI. The down pipes were coated at an additional charge. These parts today would be about $1125 not including tax and shipping. Plus the wait time it takes to get them. The coating on the down pipes is special order. The downpipes...

Headers still available.

PM sent to Lucky13vrscb

Price reduction $800obo Plus shipping.

Tti small block Mopar shorty headers part #TT134025. These have been thermal coated. With a ceramic finish 1 5/8 tube to 2.5 inch collector. Down pipes are part #T340440AS-C4 and were thermal coated at an extra cost as well. One has been “massaged” as shown. These headers are off a 1967...

TTT

Good used Proform electronic distributor, Jegs blue ignition box, a good used coil. and a good used set of plug wires. Included are some extra spare plug wires and some other spare parts. Worked when pulled recently. $90 Parts are in 94928, I’ll ship on your dime.

Bump

Edelbrock air gap part 7576. Fits small block Mopar La. Comes with eEdelbrock intake bolts $380 Pick up in 94928, or will ship on buyer dime.

Not sure of the difference. Sold the box last night.

Price drop $65 shipped.

$210 shipped. Open to offers

Price reduction to $280 plus the ride. Open to offers.

Mopar power steering box 3643311. Came off a 74 duster. Good condition. $70 shipped, way less if you pick up. Located in 94928

Small block.

The bell housing has a bearing retainer diameter of 4.80. Just the bell housing and the clutch fork pivot. I can’t find a part number the bell housing. $300obo plus the ride. Located in 94928.

Has anyone used the engine/transmission mount kit with the Holley swap manifolds on a 5.7/6.1 and a Nag1 trans? How did it fit? What steering did you use? Thanks!

Price drop $215 shipped Also includes the alternator pulley cover.

March single grove water pump pulley, crank pulley and alternator bracket. Crank pulley #10009 Water pump pulley #10212 Also included is the alternator bracket and misc hardware as shown. $225 shipped and insured usps to the lower 48

Transmission was attached to a 340.

The case is a 1967 casting with a 23 spline input/30 spline output shafts. I used the yoke from my 727 when i did the swap.

Selling my 4 speed set up from my 67 dart. Removed from running/driving car a few weeks ago. I purchased this rebuilt transmission from brewers in 2016. (I have documentation) There is about 3800 miles on it since installation. Works great. Has a 3.09 first gear. Cast iron bell housing...

Yes, it is still available. I picked up the engine about 9 years ago and it was already rebuilt. The car it went into has been on and off the road since then. I don't know how many total miles. I've put about 8k on it since i've had it. According to my speedometer. It is in my 1967 dart...

First off-I cannot read the Vin stamped on the block. Pictures included, could not see the vin on the pan rail. 340 engine for sale. Runs good, compression 125-140. Oil pressure 70 cold, 25 hot. I can send a video of it running if your serious. If you are local, you can see it running. I will...

Hello, I am looking for a 73-76 V8 spool mount K frame/member. Let me know the price and depending on location, if you are willing to ship. Thanks, Rob

Price drop $415 for the manifolds and pipes.

Price drop $425 for the manifolds and pipes.