Search results for query: *

I still use the washer today and after adding it and changing the belt to gates had no problems since this posts 2016.. JINX!

Part number of the belt? It was a gates 7480 XL. If I remember correctly I also added a washer between the sleeve bushing and the alternator bracket which stopped the vibration that I believe was causing the belt to jump at hard acceleration.

Thanks for the descriptor and yeah man, once I started it just snowballed lol

thx brother. All is well, I hope you and the fam are also. :)

With the Motor back together I got back to installing the Fitech system. After locking the distributer and installing it I set the timing as instructed. For me I set it up alike this. Fitech engine set up: -> Crank mark 15 BTDC -> Distributor reluctor on pickup -> Phased rotor 60% advance of cap...

Long time no post but I finally got caught up. I bought a set of Comp 1622-16 ultra pro magnums and longer pushrods to go with them. The stocks pushrods were too short. While I was in there I swapped the eddie performer with the performer RPM. and bought a thermostat housing riser to accommodate...

Yep still in there got the plunger out. Think I can replace that without pulling the manifold? Ever try it?

Yeah, the rods were right I think that happened when it pushed through. Definitely looking into a new rocker setup.

means a lot of pb&j with steel cut oats for a while.

Something like these COMP Cams 1622-16?

Doh! Lesson learned.

These are the details on the cam and springs. Xtreme Energy HI-LIFT 231/237 Hydraulic Flat Cam for Chrysler 273-360 Dual Valve Springs: 1.437" O.D. Outer, .697" I.D. Inner-1

Stock 340 rockers.

Well it’s slow going because other things but more good news. at least in nudged in there. That’s good.

I know. It had me baffled.

Thank you. This stuff happens lol Pulled the rockers and will replace them and the rods.

No clue. Those were new rockers and had less than 5K on em. I ordered new ones and push rods since the others were curved. I timed two more pieces from the head and put a very strong magnet on the oil pan. We’ll see where it goes after that. Of it happens again I’ll changed the springs. AlV

What up FABO FAM, I want to give an update on my recent escapades. Per my previous post started a project to install FItech EFI and install Classic auto air under hood kit ne compressor brackets receiver and hoses to the factory evaporator and controls. This is a bit long but should be...

Thank you, these are perfect and the extra piece!! Nice doing business with you. I have them soaking now and will blast and spray them tomorrow. Will post pictures. cheers AlV

Perfect. Thx. I’m at 08859. Pm me your PayPal or Zelle account info with price plus shipping and I’ll transfer the funds.

WTB for a 1969 Dart. AC drier bracket and strap. thx! AlV

Alright alright alright…. Do you have FI? No i don’t. Well it be cool if you did… lol. I finally broke down and decided to do the swap. FItech setup go efi 30002 with the force fuel mini. Goals Ease tuning through software Improve drivability. Improve throttle response. Improve fuel...

It's been a while but I think I was able to get those from RTspecialties and Dantes but I think both those vinyl trim clips and the rocker molding clips are pretty available today. Try the two shops I mentioned, classic may have them now. I know when I was l restoring the GTS I had to horse...

I just replaced the switch since the oil was coming through the body.

Hi RRR, thanks! The Lift is a Danmar two post. It comes with lift adapters for extra height, 6” and 8” that can be combined for additional 14”. It has two pad, saddle and round plus pinch-weld cushions. The pump is a 110/220 I have wired for 220. The lines are connected to the cylinders using...

Thanks for the heads up. I just cleared out some.

Your eyes don’t deceive…It’s a short post lift lol

Guess whos back on the rack! The transmission has had a slight leak for the last year and a half. Turns out the Neutral safety switch is leaking through. Happy about that.. cheap ez fix. Been thinking about fuel injection. Interested in hearing thoughts. cheers!

Wow! Thanks! You’re too kind. Sorry just seeing this.. I’ve been away for a bit.

Snow is here but thinking about this