Search results for query: *

  1. M

    [FOR SALE] Assorted lot

    PM sent on AC/Heater control switch
  3. M

    [SOLD] Small block adjustable rockers iron

    PM sent in case other fall through.
  4. M

    [SOLD] 26" OEM style 3 row radiator

    Interested, PM sent.
  5. M

    [SOLD] Trip Down The Clearance Aisle

    I'll definitely take both of #11 please. Potentially #20 also. PMing for more info.
  6. M

    [FOR SALE] still cleaning

    PM sent on trans pan.
  8. M

    [SOLD] Clean out in the "E body " Aisle

    I'll take the defroster setup #19 and your best gas pedal from #6.
  9. M

    [SOLD] Factory Hydraulic Roller Cam (1987)

    PM sent.
  10. M

    [SOLD] 360 Milodon Baffled Oil Pan

    Also interested. PM sent.
  11. M

    [SOLD] Magnum Hydraulic Roller Cam

    PM sent
  12. M

    [SOLD] Magnum Hydraulic Roller Cam

    Were you able to use this cam with stock magnum lifters and intermediate shaft? Or does it require a bronze gear / aftermarket exposed wheel lifters?
  14. M

    [SOLD] Mopar Performance 576 Heads

    These are essentially 308s without the smog pump provisions. A few were apparently sold with T/A pushrod hole placement. The exhaust short and long turn radius were inspired by/more similar to W2 than other LA heads but not W2 ports by a long shot. The designer had other improvements in the...
  15. M

    [FOR FREE] Free parts

    Location?
  16. M

    [SOLD] Valve Cover Breather, 2-nipple, NEW

    PM on the way.
  17. M

    [SOLD] SB Probe rockers

    Do you have a part number for these or know the ratio? I can't find a reference to Probe making mopar rockers so any info would be good.
  18. M

    [SOLD] Mopar performance blockparts

    Second in line please. Also unable to PM you.
  20. M

    [FOR SALE] Trick flow springs, revnator, etc....

    PM sent on the RevNAtor. Well tried to anyway FABO says your inbox is full. The 140 includes the cost of shipping yes? How long was the unit run? Performance gain quotes aside, did everything work as advertised ie, rev limiter, no vacuum advance needed?
  21. M

    [SOLD] E body 8 3/4 rear.

    PM sent
  22. M

    [FOR SALE] 741 case open 3.55's

    ttied to send PM but your inbox is full. Shipping to 31907? small or large yolk?
  23. M

    [SOLD] 750 Street Demon Carb 1904

    PM sent
  24. M

    [SOLD] SB SFI Flex Plate

    PM sent.
  26. M

    [SOLD] 273 adjustable rockers and spacers (cores only)

    PMs replied. Sale Pending. And SOLD. In record time. Thanks FABO!
  27. M

    [SOLD] 273 adjustable rockers and spacers (cores only)

    Got these as part of a package deal and won't be using them. No adjusters, no shafts, no mounting hardware. They appear to have been sandblasted at some point, but have picked up some surface rust over the years. Will definitely need cleaning and to have the tips resurfaced. May also need...
  28. M

    [SOLD] Comp Cams 995-16 Valve Springs

    Comp 995-16 springs. I got these as part of a package deal and won't be using them. They've been sitting for a while and a few have small areas of surface rust. The pic is one of the worst ones in the bunch, for reference you can see the spot on the top of the outer. Will probably some clean...
  29. M

    [FOR SALE] Mopar high performance w2 heads

    PM Sent
  30. M

    [WANTED] LD340 intake

    Did you get my PM. I am interested.
  32. M

    [WANTED] LD340 intake

    Thanks rumblefish360, and yes there is a reason. I used to have an air-gap, personally I don't see what the big deal is with them. I replaced it with a stealth which I feel is a much better intake, at least on my combo. I was going to use it, but I'm wanting to build a sleeper street strip...
  33. M

    [WANTED] LD340 intake

    I don't mind putting in a heli-coil or two, and cleaning myself. But, manifold would have to be guaranteed to fit stock heads. No machined sides and no major corrosion in coolant passages. I've seen these pass recently in the 150-200 range (before I decided to use one of course) That's the...
  34. M

    [SOLD] unused Eagle SIR6123CP small block I beams $220 shipped

    Cleaning out the parts closet. Unused Eagle SIR rods. Length 6.123 un-bushed small end for pressed wrist pins. Only one has even been out of the bag. These are the cap screw design and you can see in the pic. Since the one was open I took it apart to show the cap screws and popped in a set of...
  35. M

    [SOLD] unused MP ductile iron 360 4 bolt main caps $80 shipped

    Cleaning out the parts closet. I bought these from a member on another mopar site a while back and won't be using them. So I decided it is time to give someone else a go at them. These sets did not come with a #5 because the factory units are so beefy to begin with. The number 4 has some...
  36. M

    [SOLD] used small block M/T valve covers $65 shipped

    Cleaning out the parts closet. These have been sitting a while before I found them. They look like they were previously sand blasted, but not very well as seen by a little black paint hanging on between the fins near the breather knock outs. Looks like at least one of them was actually knocked...
Back
Top