Search results for query: *

  1. StevieMac

    Identify which switch I need

    So, if you look at the parts list, all I see are two speed switches, hence my question. Since replacements are so expensive, I thought that I would ask others instead of just throwing money away.
  2. StevieMac

    Identify which switch I need

    Thank you MoparMike
  3. StevieMac

    Identify which switch I need

    So I think this is the correct switch, 2770380. Thoughts? Washer/Wiper Switch# 2770380 - Variable - 1970-71 - A - E - Body - NOS - Washer/Wiper Switch - Switches - Electrical - Parts
  4. StevieMac

    Identify which switch I need

    So looking at this, it looks like a 3 speed based on your description, correct? If so, which switch should I look for? Thanks again!
  5. StevieMac

    Identify which switch I need

    Hello All, I have a 70 Duster that was a /6 and now has a 340. When I bought the car, it didn't have the wiper switch in it. I have looked at mymopar.com to try to get a part number so I could see if one is available out in the world, but the one that is listed there doesn't appear to match...
  6. StevieMac

    Engine reving to full throttle on start

    Thanks everyone, after getting it off the trailer and re looking in the carb, I found the below piece in the passenger side secondary. After getting it out by taking off the carb, I can run the car without it trying to grenade itself. I didn't put the piece back on the carb yet, but it is now...
  7. StevieMac

    Engine reving to full throttle on start

    I have a 70 Duster with a 340 in it. Was running great without any issues, and when driving home the other day, the engine RPMs just started to sky rocket like at full throttle. I turned off the ignition and coasted to the side of the road to check it out. I check for stuck linkage, and...
  8. StevieMac

    NC and SC

    Where is your yard hemiperry?
  9. StevieMac

    Need a little bit of wiring assistance

    Thanks everyone. Since I had a extra light switch, and need to add a wiper switch, I went ahead and popped the dash out. Took about 15 minutes... Replaced the switch and before I reinstalled, I thought I would try it. Still no joy. Get headlights, but that is it. Turn signals still work...
  10. StevieMac

    Need a little bit of wiring assistance

    I have a 70 Duster that is just giving me fits with some of the electrical. Simply put, I am not an electrician and I am trying to figure this out.... When I pull the light switch out, I get headlights, but no tail lights or dash lights. If I turn the knob, the dome doesn't come on either...
  11. StevieMac

    1973 340 Duster goes in for a paint job...

    Where are they located??? I have a 70 Duster
  12. StevieMac

    headlight relay install - before and after photos

    @crackedback What is the cost of this kit??? Thanks
  13. StevieMac

    NC and SC

    70 Duster and I also have a 16 Hellcat
  14. StevieMac

    Leaning to the driver side...

    Thanks everyone. I will do the uca bolts first then try the torsion bars...
  15. StevieMac

    Leaning to the driver side...

    Ok, thank you. On a side note, how's Omaha? Graduated from Bellevue East many years ago...
  16. StevieMac

    Leaning to the driver side...

    I'm assuming you are talking about the torsion bar... I have yet to do that, but will try that tomorrow. If I remember correctly, you turn in clock wise to tighten, raise, the front. As for the rear, yes, it is a little lower on the same side, but I have air shocks on it. Was thinking of...
  17. StevieMac

    Leaning to the driver side...

    Hello FABO. Got a problem with my 70's duster. It needed upper and lower ball joints in a bad way. I put QA1 upper control arms on it with new lower ball joints from Moog. While I was at it, I put new inner and outer tie rod ends and shocks all the way around. Now I seem to have a leveling...
  18. StevieMac

    NC and SC

    Between Greenville and Anderson SC
  19. StevieMac

    Help with upper ball joint stuck in kuckle...

    Was thinking of converting to wilwood disc setup, but they use the current spindles. Not sure where to find new ones at a good price
  20. StevieMac

    Help with upper ball joint stuck in kuckle...

    Ordered from Amazon. Thank you everyone!!!
  21. StevieMac

    Help with upper ball joint stuck in kuckle...

    Do you know where I can get this separator??? Thanks everyone!!!
  22. StevieMac

    Help with upper ball joint stuck in kuckle...

    So you are saying to heat and bfh it?
  23. StevieMac

    Help with upper ball joint stuck in kuckle...

    I have a 70 Duster that I just bought and I knew that it needed somethings done to the front suspension to drive it safely..... So I am putting new tie rod ends, QA1 upper control arms, bump stops, etc.... Got one side torn appart, was using a pickle fork to remove the ends and upper ball...
  24. StevieMac

    65 Barracuda floor pans.

    Thanks!!! Exactly what I needed
  25. StevieMac

    65 Barracuda floor pans.

    Please share....
  26. StevieMac

    65 Barracuda front disc brake swap

    I changed my drums to disc using the wilwood setup... http://www.summitracing.com/parts/wil-140-11023-d/overview/year/1965/make/plymouth/model/barracuda Didn't have to change any a arms or anything....
  27. StevieMac

    Front parking brake cable advice

    Did yours seem a little short? Mine that I just ordered from inlinetube is about 2 inches short on my 65 Barracuda...
  28. StevieMac

    65 barracuda parts car? Worth it or not.

    Send me a pic of the lower front valance... I might be interested in that...
  29. StevieMac

    Swapped out to Electric, now no spark... :(

    Thanks Kit. I will go check that out.... Should have mentioned that this is not a dual ballast....
  30. StevieMac

    Swapped out to Electric, now no spark... :(

    So I read the "Fool-proof tips to fix any NO-SPARK issue" and read numerous other threads on here, but it is still not working.... Here is the back ground.... I swapped out to the mopar electronic ignition on a 65 Barracuda with a 360 V8, and now I am not getting any spark from the coil...
Back
Top