Search results for query: *

Hi, looking for a 904 trans yoke for driveshaft,I think it is 25 spline. Thanks.

engine is 79 318 with 5 qt. pan. total including shipping to 35077. Thanks, Double Six.

How do you remove the dipstick tube from the block without breaking it?:???:

if you use a high volume oil pump in a 5qt. pan will it pump it dry or will it be ok.? Thanks, Double Six:???:

Well to start things off, we had purchased a newly rebuilt 318 from a friend and tried putting it in the 67 Barracuda that I'm helping my son get up and going again, today, but it didn't go so well . We had it almost in, but the oil pan would not, and was not, going to clear the steering...

Does anybody know which speedo gear(how many teeth) would go on 67 barracuda, came with 273 4bbl. 71/4. Sorry, I don't know what gear ratio. Thanks, Double Six.:???: [/B]

new to this trans thing,what are the 2 holes for on left side of trans cover? I think one may be speed ometer cable,what would the other be ? Thanks ,Double Six:???:

What size bolts and how long should they be and I'm guessing grade 8 correct Thanks ,Double Six:burnout:P.S. fine or course thread

I am looking for a front valance and drivers door for 67 Barracuda notchback. Thanks,Double Six:burnout:

Hey Guys, will a 69 Dart A/T crossmember and mount fit a 67 Barracuda, both came with a 273-904.Thanks!!

Hey Guys,I need a crossmember and transmount for 904 . 67 Barracuda. to Hanceville, Al 35077 Thanks!!!!

Hey Guy's. What do you have to do to make this work .I know they have different motor mounts and brackets. Thanks

Hey guys, I need advice on how to remove the wheel stud flange on the axle. I have never done this so I'm seeking good advise . I am needing to replace the wheel studs. thanks...

Hi ,can someone tell me the size and length of the bolts, that hold the trans down to the mount, on a 904 -318 thanks,Double Six

Hey , will a small block engine that came with spool type motor mounts (72) fit onto brackets with the older style motor mounts(69) Thanks, Double Six

Hi, I was wondering if a slant 6 water pump pulley will fit a small block water pump? thanks, Double Six

I need a sigle groove water pump pulley for 69 318. thx,Double Six

I have a 69 318 that I am going to beef up a little. I see no oversize markings on piston tops but they have 4 valve reliefs are these stock or has this engine been built before? I haven't had a chance to mic cylinders yet. thx, Double Six

Hi , I got a question ,do 904's and 727's have the same dipstick and tube ? Thx, Double Six

I need a oil dipstick for a 69 318 . also need tube and dipstick for 904 tranny. thx,Double Six

yeah, I am wanting a set of 73 and up 318 rods in good shape. building a screamer thanks, Double Six

This is first attempt at this primarily by myself,so I'm asking is this the way it goes together when hooking up? ( engine ,flywheel,flexplate,bellhousing which houses tork converter and trans) thx, Double Six. oh, I forgot to tell you this, we are putting engine and trans in together...

I picked this up this week for 50.00 the guy said it was driving when they took it out. He said it came out of a 71 Duster with a 360. I got the numbers off of it today and was wondering if anyone could tell me for sure what it came out of. bellhousing 452-2 right front side of tranny...

Hey to everbody on the southeast board. My son and I have a 67 barracuda notchback we're trying to get rolling again.My wife has a 68 dodge coronet 500 sedan. I'll be checking back in soon,glad to know about this forum ,it;s been a lot of help already. Later.

I was taking rear seat out of my 67 barracuda which I knew was not original and found this broadcast sheet for a 72 dart/demon. vin # LH23G2B435705. If you have this car,show proof of ownership by registration or title and I will send it to you. pm me.

Help, I am looking for a pair of motor mount brackets for small block 318 to go in 67 barracuda. thx.