Search results for query: *

I am looking for the pinch block and allen head screw that ties the vent window frame to the inner door structure for a 1969 Barracuda. Here is a picture of what I'm looking for.

I have a 1998 Mopar Preformance crate 360 installed in my 1969 Barracuda convertible. The engine is an LA block with Magnum heads. It has an Edlebrock Air Gap dual plane manifold and a Comp Cam (20-614-9) with the following measurements: 264/274, .480/.480, .210/.220 @ .050 lift, 112 deg lobe...

I have a slightly used (less than 6 months) vacuum pump for power assist brakes. If you have a engine with a tall cam and you don't produce enough vacuum from your power brakes to operate correctly, this pump to will the necessary vacuum to the braking system. This unit has an internal switch...

For Sale: slightly use water neck/thermostat housing made by CSR Performance Products. This unit works and looks great. I changed intake manifolds and was not able to reuse this piece. It's made from billet aluminum with a clear anodize finish. The head swivels 360 degrees to optimize your upper...

Finally found out what the clunking (techincal term) was making all the noise when shifting from 1st to 2nd (Torqueflite 727). Where the driveline and 3rd member meet at the U-joint appear to be hitting the underside of floor just above teh rear axle. This happens during shifting or when I hit...

I just had the transmission (Torqueflite 727) rebuilt because the reverse servo went out and also took out the reverse band. While the transmission was a part the shop also changed out the valve body so the reverse lights would work with the roster and neutral switch. Now, the transmission...

The long build of the car is done and now I have a few extra parts. I have a set (4 pieces) of fully polished stainless steel trim that goes around the windshield (outside) for a '67 thru '69 Barracuda and/or Dart convertible. I don't have the piece that goes under the windshield wipers. This...

Anyone know where these may go on a 1969 Barracuda Convertible? Thanks in advance for the help.

I have a Magnum crate 360 mated with a TorqueFlite 727 transmission. The rear end is a Dana 60 from Strang Engineering with a 3:54 to 1 ratio. In 3rd gear when the car is doing 60 mph the engine is turning at 3,000 rpm. This seem way to high of rpm to me. Do I need a taller rear end gear...

Has anyone used a Holley Transmission Kickdown Bracket on a Holley 750, 4 barrell carb with a TorqueFlite 727? My setup is a Holley 750 and 727 and we are having a problem with the trans shifting down from 3rd to 2nd or 1st when you step on the gas while in 3rd gear. I'm looking at the Holley...

I have a camshaft for sale removed from a Mopar Performance Crate 360 (LA block with Magnum heads). The engine was rated at 380hp and 410 ft-lbs of torque with this cam and the M1 manifold (also for sale). We did a cam and intake manifold swap to make the car more driveable at lower RPMs...

I have for sale a M1 Single Plane Intake Manifold recently removed from a Mopar Performance Crate 360 (LA block with Magnum heads). This engine only has 150 miles on it. We removed the manifold in favor of a dual plane Edelbrock RPM manifold. This manifold is nearly brand new. I also have the...

This starter is better suited for a manual transmission. I had it installed in a Torqueflite 727 transmission for 3 months. Its almost brand new. The shop that rebuilt my transmission suggest a 9523 so I changed. I now have this nearly new starter available. Price: $175 plus shipping. I'm...

We are having a new, more mild cam installed into the 'Cuda. The installer called me last Friday and said the cam will not seat into the engine. Upon further analysis and comparing the new cam to the old one that came out of the engine (crate 360), the first cam bearing (closest to the...

A few of my buddies and I recently completed the build of a 1969 Barracuda convertible for my buddies wife after my buddies untimely death. My buddy bought a Magnum crate 360 engine for the car. After installing it and getting it started we noticed very little braking. Further investigation...

The 727 Torqueflight in the '69 Barracuda we just got done with now will not go into reverse. We finished the car (for the most part - these cars are really never done) back in Sept. '14. I've only put 150 miles on the car since then. I last drove it in December and it ran fine - shifted thru...

I've got a potential issue with my fuel pressure. At the guage mounted inline with the fuel line to the carb, the pressure is reading 1.5 psi. The engine just quits while sitting at a red line but not all the time. However, it goes down the road just fine. We originally set the fuel pressure at...

For Sale is a 2007 Chrysler 300C SRT8 in near perfect condition. Located in Seattle, WA 98109 Price: $24,500 OBO (Craigslist Link: http://seattle.craigslist.org/see/cto/4697400052.html Payment Methods Accepted: CASH $$$, PayPal Description: See Craigslist ad for more details. This is a 2007...

Can someone help identify where I can get 10 of these "spacers"? They go on the 2 side rails that hold down the convertible top. They are for a 1969 Barracuda convertible.

What are peoples thoughts about repair or replacement of a transmission cooler lines? Compression fitting or replace complete line?

I just installed the door on the '69 Convertible Barracuda. I have the convertible door alignment wedges sold by Classic Industries but can't figure out where they go. The doors fits great. Do I need the wedges? If so, where do they go. Pictures would be much appreciated. Thanks.

I am almost done with installing the door hardware - window regulators, windows, lock mechanisms, door handles, wing windows, etc... I need help identifying the part in the attached pictures. This part goes above the latch mechanism stricker plate and appears to marry with an indentical part...

I need help (pictures would be great) on how to install the A-Pillar weatherstripping inside the door jam. This is teh long skinny weatherstripping that butts up against the wing window and forms a seal between the wing window and the inside of the A-Pillar. It's on a 1969 Barracuda...

Anyone have a suggestion on the brand and/or type of transmission fuild to put in a Torqueflite 727 Automatic transmission? How about quantity? We're going to fire up the car for the first time this weekend and both the engine and transmisssion are brand new. Any help would be much appreciated.

I need an untinted passenger side door glass the 1969 Barracuda Convertible. Does someone know where I can get that? Does someone need my factory tinted front passenger side door glass as trade?

I have 2 driver's door windows for the '69 Barracuda. One has a knob (lack of a better word) located in the lower left of the window and the other does not. Which one is correct? The part I am questioning is item 77 & 78. Does anyone have an idea of what this is for and if it is convertible...

I'm at the point of assembling the doors on the FISHRAG ('69 Barracuda Convertible) and I need help. My buddy disassembled everything from the doors prior to painting the car. Does anyone have pictures of the doors during assembly showing how and where to assemble the window cranks and windows...

Was there ever an option for a remote (electric) trunk release mechanism in a 1969 Barracuda Convertible? The one I'm restoring has an electric release latch but the OEM wiring harness (Year One) reproduction does not have a provision for this option. If Plymouth made that as an option, where...

This is what is on the first screen before you can post your ad. Your welcome to place as many 'For Sale' ads as you like, but we ask that you follow these simple rules: No Phone numbers or eMail addresses in ads; Post accurate Photos of the item your selling if you can Post the location...

As the title reads, can someone tell me what these pieces are and where they go? I have 4 of them and they each have a small u-shaped clip. They look like they go in the interior somewhere. This is for a 1969 Barracuda Convertible. Thanks for the help.